GSS PSPT 1000 Assembly Instruction Manual Download Page 3

Page: 3 / 33

- 3 -

PSPT 1000

COFDM parameters ....................................................................24

Setting the output signal .................................................................27

Bandwidth of the output signal .................................................27

Carrier modulation .................................................................27

Spectral position.....................................................................27

Setting the transmission parameters ...............................................28

Transmission mode .................................................................28

Code rate ..............................................................................28

Guard interval .......................................................................28

Displaying the output data rate......................................................29

Setting the transport stream / ORGNET-ID ......................................29

Network Information Table (NIT) ....................................................30

Saving settings ............................................................................31

6 Final procedures ........................................................................................31
7 Channel and frequency tables ....................................................................32

Summary of Contents for PSPT 1000


































Search results

Summary of Contents for PSPT 1000

Reviews:

Related manuals for PSPT 1000

Brands by name

Popular brands

GSS PSPT 1000, Assembly Instruction Manual

Search results

Summary of Contents for PSPT 1000

Reviews:

Related manuals for PSPT 1000

Brands by name

Popular brands