GSS HDMT 263 Assembly Instructions Manual Download Page 13

Page: 13 / 22

- 13 -

HDMT 263, HDMT 265

5.4 p

rogr a mmIng

the

module

Notes:

– Entries are saved by pressing the button.

—> You will be returned to "

Selecting the module/channel strip

– The programming process can be cancelled by pressing and holding the

button.

—> You will be returned to "

Selecting the module/channel strip

• Switch on the

head-end station.

SETUP

V 8

Ein/On

BE160

—> The display shows "

SETUP BE160

" and the software version of the

head-end station (e.g. V 8).

—> The output level of the output collector can be adjusted in the "

SET-

" menu (see STC 160 assembly instructions).

electIng

the

module

channel

strIp

—> The programming procedure of the channel strips "

" and "

" is

identically.

Bx 1A
C5-12,S3-24

TWIN-SAT

C07

Böx 4
C5-12,S3-24

TWIN-SAT

C07

Bx 1B

DVBT

C23

Bx 1A

DVBT

C21

• If necessary, press

repeatedly to select the particular module (

…)

or channel strip "

" or "

" to be programmed.

Summary of Contents for HDMT 263























Search results

Summary of Contents for HDMT 263

Reviews:

Related manuals for HDMT 263

Brands by name

Popular brands

GSS HDMT 263, Assembly Instructions Manual

Search results

Summary of Contents for HDMT 263

Reviews:

Related manuals for HDMT 263

Brands by name

Popular brands