GSS GAK 7100 Assembly Instructions Manual Download Page 6

 

 

- 6 - 

HOC 168

i

nstalling

 

the

 rf 

output

 

ColleCtor

  Before installing or changing a module or accessory, switch off the head-end 

station or unplug the power cable from the mains power socket. 

 

•  Remove the front cover and the base plate of the STC 160 head-end station 

(see STC 160 assembly instructions).

3

A

E

F

1

Fig. 4

 

•  Connect  the  ribbon  cable 

3

 

(fig.  4,  part  of  the  packing 
contents  of  the  head-end  sta-
tion) to the connector block 

B

 

(fig. 1) of the RF output collector 
HOC 168.

 

•  Connect the other end of the rib-

bon cable to the backplane 

E

.

 

•  Connect  the  output  cable 

1

 

(fig. 4, part of the packing con-
tents of the head-end station) to 
the  output 

A

  of  the  RF  output 

collector.

 

•  Insert  the  other  end  of  the  out-

put cable in one of the openings 
(knock-outs) in the rear panel of 
the head-end station 

F

 and tighten it.

 

•  Mount the RF output collector HOC 168 to the position in the head-end sta-

tion according to fig. 4.

 

•  Fasten the outer sockets of the RF output collector 

2

 (Fig. 5) with two nuts 

and lock washers put under.

2
C

D

Fig. 5

  Tighten the nuts until the teeth on the lock washers have penetrated the exte-

rior coating and a good connection is made between the housing and the RF 
output collector.

Summary of Contents for GAK 7100










Reviews: