GSi 40 Series Construction Manual Download Page 83

Page: 83 / 116

Roof Panel Instructions

1. For better results in erecting the roof, install one roof panel (B) in three places.

2. After these three panels (B) are in place, the peak assembly should be centered.

3. Install intermediate panels making sure to lap them counterclockwise until all panels are in place.

NOTE:

Do not tighten the bolts until the roof is completely assembled. Make sure to overlap
the adjacent panels in counterclockwise direction as shown.

NOTE:

Do not install bolts onto the holes for roof ring locations until the roof rings are
installed. Refer to

Installing a Roof Ring, page 89

Figure 8-5

Roof panels installation direction

Center collar (CRP-4608)

5/16 in. flange nut (S-3611)

Roof panel (CTR-0386)

Upper rib

Roof flashing (CRP-4684)

Lower rib

5/16 x 1 in. flange bolt with sealing washer
(S-10260)

4. Install the eave clips (I) and intermediate eave angles (L) on the top sidewall with the 5/16 x 1 in.

flange bolts (D) and 5/16 in. flange nuts (E).

NOTE:

The intermediate eave angles (L) are installed between two eave clips (I).

5. Fasten the roof panels (B) to intermediate eave angles (L) on the eave end and to the roof

flashing (C) on the peak end.

6. When installing the roof panels (B), take into consideration placing the manway for ease of access

to the sidewall and roof steps (K).

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands