GSi 40 Series Construction Manual Download Page 89 | Manualshive

Page: 89 / 116

background image

Chapter 8: Roof Assembly

Installing a Roof Ring

Quantity and part numbers of roof ring kits vary with the location placement and with the size of each bin.
The following procedure will be similar for each kit.

What You Should Know

The roof ring and threaded stud may become dislocated from each other during high winds or when the
inside pressure of the bin is too great. If a threaded stud is dislocated, the entire roof ring will become
disjointed. Prevent this by staking the expansion bolt threads at the jam nut location (after the rings have
been installed and expanded to the correct size), use of suitable thread locking compounds or other
effective methods. Refer to

Figure 8-11, page 90

.

1. Determine the quantity of roof ring clips (C) needed for the roof ring section (B) being installed.

NOTE:

Each roof panel rib must have a roof ring clip installed.

2. Install a 5/16 x 1 in. flange bolt (A) to the roof ring clip (C), and install a sealing washer (E) to the

underside of the roof ring clip (C).

3. Slide each assembled roof ring clip (C) onto a roof ring section (B), and position each roof ring

clip (C) over each roof panel rib.

4. Install a 5/16 in. flange nut (D) to each roof ring clip (C).

NOTE:

Do not tighten hardware until all roof ring sections have been installed.

Figure 8-10

Exhauster roof ring shown

A

5/16 x 1 in. flange bolt with sealing
washer (S-10260)

D

5/16 in. flange nut (S-3611)

B

Roof ring section

E

Sealing washer (S-10303)

C

Roof ring clip (R-997)

PNEG-4336

36 Ft. Diameter 40-Series Bins

89

«
...
87
88
89
90
91
...
»

Summary of Contents for 40 Series





















































































































Reviews:

No comments

Related manuals for 40 Series

Brand: Qingdao H.Y Pages: 6

Brand: Landoll Pages: 83

Brand: Danfoss Pages: 106

Brand: Garden Treasures Pages: 2

Brand: Yamaha Pages: 178

Brand: Yamaha Pages: 15

Brand: Yetter Pages: 24

Brand: Yetter Pages: 32

Brand: MadLab Pages: 7

Carestation 620

Brand: GE Pages: 268

Brand: GE Pages: 50

Brand: Daekyung Pages: 15

Brand: Atlas Metal Pages: 2

Brand: Channel Master Pages: 7

Brand: Desisti Pages: 11

Brand: Sygonix Pages: 8

Brand: RAK Pages: 50

Brand: Tuttnauer Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands