GSi 40 Series Construction Manual Download Page 49

Page: 49 / 116

Chapter 6: Stiffeners

Base Boots

Use the following information to determine the differences between the base boots.

Figure 6-7

Images of the base boots

Call Out

Part Number

Description

Height

Base Plate Size

CTS–4045XX

Base boot weldment for 8 through
a laminated 2 Ga. with an 11 Ga.
insert

11.391 in.
(29 cm)

6 x 9 x 3/4 in.
(15 x 23 x 1.90
cm)

CTS-4046XX

Base boot weldment for 16
through 9 Ga. base stiffeners

11.391 in.
(29 cm)

6 x 9 x 3/8 in.
(15 x 23 x 0.95
cm)

CTS-4048XX

Base boot for 2 Ga. laminated
base stiffeners with 10 Ga insert

11.391 in.
(29 cm)

8 x 10 x 3/4 in.
(20 x 25 x 1.90
cm)

CTS-4049XX

Base boot weldment for 2+8 to 2
+2 base stiffeners

11.391 in.
(29 cm)

8 x 10 x 1–1/2 in.
(20 x 25 x 3.81
cm)

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands