SCC 3400 RDS / SCC 3460 RDS / SCD 3490 RDS
Allgemeiner Teil / General Section
GRUNDIG Service
1 - 11
ENGLISH
11
2
Once you have selected the function you require, set the level
using the »
VOLUME
« knob.
– Display: Bass level raised by »
+09
«.
3
To finish the setting keep pressing the »
SOUND
« button until
the selected station appears in the display.
Note:
After approximately six seconds the device quits the selected
function (FADER, BASS, TREBLE, BALANCE) automatically.
Loudness
The
LOUD
(Loudness) function raises the bass and treble levels to
improve the sound at low volumes.
1
Press »
LOUD
« until you hear a signal.
– Loudness is activated.
2
Press »
LOUD
« again.
– The function is deactivated.
BASIC FUNCTIONS
__________________________________
LOUD
O N
LOUD OF F
RADIO N1
BASS +0 9
ENGLISH
25
To make the use of the device as simple as possible, a number of
custom settings which are only required once or very occasionally
are located on a special operating level (EXPERT).
Optional EXPERT settings
Code settings (»
CODE
/
SAFE
«).
Display contrast (»
DISPL 00
«).
Security LED on/off (»
BLK OFF
/
ON
«).
Signal tone on/off (»
BEEP OFF
/
ON
«).
Deactivate AM band (»
AM OFF
/
ON
«).
Automatic traffic news search on/off (»
TP-IS OFF
/
ON
«).
Automatic change of regional stations on/off (»
REGOFF
/
ON
«).
Switching on and off with ignition (»
IGN OFF
/
ON
«).
Muting in car phone mode (»
PHONE OFF
/
ON
«).
Input sensitivity in CD or DAT mode (»
MCD
«).
Volume limit after switching on (»
ONVOL 00
«).
Minimum volume for traffic news (»
TRVOL 00
«).
Changing EXPERT settings
1
To enter expert level keep pressing »
EXP
« until you hear the
signal.
2
Press »
<
« and »
>
« to select the required EXPERT setting (see
above), for example volume limit on switching on.
3
To activate it, briefly press the »
EXP
« button.
– Display: »
ONVOL 12
« flashes and you can hear the selected
station at the selected volume.
4
Press »
<
« or »
>
« to select the required volume. Press the »
<
« or
»
>
« buttons to increase or decrease the value incrementally, or
hold them down for a rapid run-through.
5
Briefly press »
EXP
« to conclude the setting.
– Display: »
ONVOL 10
« ceases to flash.
6
To select the next setting repeat steps
2
to
5
.
7
To quit expert level keep pressing »
EXP
« until you hear the
signal.
EXPERT LEVEL
_______________________________________
ONVOL 1 0
ONVOL 1 0
ONVOL 1 2
EXPERT
26
The individual settings
Code settings. See the detailed instructions starting on page 25.
– Coding is deactivated.
– Coding is activated.
Display contrast.
– Display: Scale »
00
« to »
60
«.
Security LED on/off.
– The security LED flashes if the device is off and so is the
ignition.
– The security LED does not flash.
Signal tone on/off.
– A signal tone confirms functions.
–
Functions are confirmed by a brief muting of the
loudspeakers.
AM band on/off
– The AM band can be selected by pressing »
RADIO
«.
– The AM band cannot be selected. The radio can only be used
in FM mode.
Automatic traffic news search on/off.
When leaving the reception area for the traffic news station you are
currently listening.
– An automatic traffic news search takes place.
– No automatic traffic news search takes place.
Automatic change of regional stations on/off.
If an RDS station offers various local programmes, the device
switches to the regional station available in the current reception
area.
– Automatic change of regional stations is possible.
– No automatic change of regional programmes.
EXPERT LEVEL
_________________________________________
AM
O N
AM
OF F
BEEP
O N
BEEP OF F
CODE
SAFE
DISPL 0 7
BLK
O N
BLK
OF F
TP-IS
O N
TP-IS OF F
REGO N
REGOF F
ENGLISH
27
Switching on and off with ignition.
– The car radio can be switched on and off with the vehicle
ignition.
– The device can only be switched on and off by pressing »
IO
«.
Note:
In this case the
A 4
contact (see page 30) must be connected to
terminal 15 of the vehicle.
Muting in car phone mode.
– Muting of the car radio is activated.
– Muting is deactivated.
Note:
In this case the telephone mute signal must be connected.
Input sensitivity for CD or DAT operation and for adapting to a CD
changer.
– Low.
– Medium.
– High.
Note:
In this case one of the sources named above must be connected.
Volume limit after switching on.
– No limit.
– Maximum volume, e.g. »
20
«.
– Display: Scale »
00
« to »
46
«.
Note:
The volume is only limited if it was higher than the value set here
when you switched off the device.
Minimum volume for traffic news.
– Display: Scale »
05
« to »
46
«.
Note:
While you are making this setting the car radio plays at the
selected volume for traffic news.
EXPERT LEVEL
_________________________________________
PHONE O N
PHONE OF F
IGN
O N
IGN
OF F
MCD
LO W
MCD
MID
MCD HI GH
ONVOL --
ONVOL 2 0
TAVOL 1 6
