Grundfos DID BF1, Installation And Operating Instructions Manual

Page: 2 / 34

English (GB)
2
English (GB) Installation and operating instructions
Original installation and operating instructions
These installation and operating instructions describe Grundfos
DID (Dosing Instrumentation Digital).
Sections 1-6 give the information necessary to be able to unpack,
install and start up the product in a safe way.
Sections 7-13 give important information about the product, as
well as information on service, fault finding and disposal of the
product.
CONTENTS
Page
1. General information
1.1 Target group
1.1.1 Qualification and training
The persons responsible for installation, startup and service must
be appropriately qualified for these tasks.
If the persons do not have the necessary knowledge, training and
instruction must be given. If necessary, training can be performed
by the manufacturer or supplier on request.
1.1.2 Obligations of the operating company
• Observe the local safety regulations.
• Instruct the operating persons.
• Provide the stipulated safety equipment and personal
protective equipment.
• Arrange regular maintenance.
1.1.3 Obligations of the user
• Read this manual thoroughly before taking the product into
operation.
• Observe the recognised health and safety regulations as well
as the accident prevention regulations.
• Wear protective equipment in accordance with national health
and safety regulations when working on the system and
handling chemicals.
1.2 Symbols used in this document
1.3 Symbols on the product
For symbols on the product see section 14. Appendix .
1. General information
2
1.1 Target group 2
1.2 Symbols used in this document 2
1.3 Symbols on the product
2
2. Safety instructions 3
3. Receiving the product 3
3.1 Inspecting the product 3
3.2 Transporting the product 3
4. Installation 3
4.1 Installation location 3
4.2 Installation of the DID
3
4.3 Hydraulic connection 3
4.4 Installing the sensors 4
4.5 Checking the tightness
4
5. Starting up the product 4
5.1 Initial startup 4
6. Electrical connection 4
6.1 Terminal connection 4
6.2 Connecting the sensors to the CU 382 control unit 5
6.3 Connecting the valve for automatic cleaning 5
6.4 Connecting further inputs and outputs
5
6.5 Connecting the CU 382 to the power supply 5
6.6 Start-up of the operating software 5
6.7 Sensor initialisation
5
7. Storing and handling the product 6
8. Product introduction 6
8.1 Product description
6
8.2 Intended use 7
8.3 Functional principle 7
8.4 Identification 7
9. Operation
8
9.1 Operating elements 8
9.2 Software overview 9
9.3 General setup
10
9.4 Parameter setup 13
9.5 Controller setup 18
9.6 Alarm setup 21
9.7 USB menu / Data transfer 21
10. Maintenance 22
10.1 Cleaning 22
10.2 Functional check
23
11. Fault finding 24
12. Technical data 25
12.1 Hydraulic specifications of DID
25
12.2 CU 382 control unit 25
12.3 Weights 28
12.4 Dimensions 28
13. Disposal
29
14. Appendix 30
14.1 Symbols on the product 30
Prior to installation, read this document. Installation
and operation must comply with local regulations and
accepted codes of good practice.
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious personal injury.
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious personal injury.
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate personal injury.
If these instructions are not observed, it may result in
malfunction or damage to the equipment.