Grundfos alpha2l Installation And Operating Instructions Manual Download Page 24

Page: 24 / 36

12.2 Installation dimensions, GRUNDFOS ALPHA2 L XX-40, XX-45, XX-50,

XX-60

Fig. 14

Dimensional sketches, ALPHA2 L XX-40, XX-45, XX-50,
XX-60

* For the UK market only.

04 253

391

Pump type

Dimensions

ALPHA2 L 15-40 130

130

129

ALPHA2 L 20-40 130

130

129

1 1/4

ALPHA2 L 25-40 130

130

129

1 1/2

ALPHA2 L 25-40 180

180

127

1 1/2

ALPHA2 L 25-40 A 180

180

135

1 1/2

ALPHA2 L 32-40 180

180

127

ALPHA2 L 15-50 130

130

129

ALPHA2 L 15-50 130*

130

127

1 1/2

ALPHA2 L 20-50 130

130

129

1 1/4

ALPHA2 L 25-50 130

130

129

1 1/2

ALPHA2 L 25-50 180

180

127

1 1/2

ALPHA2 L 32-50 180

180

127

ALPHA2 L 15-60 130*

130

129

1 1/2

ALPHA2 L 15-60 130

130

129

ALPHA2 L 20-60 130

130

129

1 1/4

ALPHA2 L 25-60 130

130

129

1 1/2

ALPHA2 L 25-60 180

180

127

1 1/2

ALPHA2 L 25-60 A 180

180

135

1 1/2

ALPHA2 L 32-60 180

180

127

ALPHA2 L 20-40 N 150

150

127

1 1/4

ALPHA2 L 20-45 N 150

150

127

1 1/4

ALPHA2 L 25-40 N 180

180

127

1 1/2

ALPHA2 L 20-50 N 150

150

127

1 1/4

ALPHA2 L 25-50 N 180

180

127

1 1/2

ALPHA2 L 20-60 N 150

150

127

1 1/4

ALPHA2 L 25-60 N 180

180

127

1 1/2

Summary of Contents for alpha2l





































Search results

Summary of Contents for alpha2l

Reviews:

Related manuals for alpha2l

Brands by name

Popular brands

Grundfos alpha2l, Installation And Operating Instructions Manual

Search results

Summary of Contents for alpha2l

Reviews:

Related manuals for alpha2l

Brands by name

Popular brands