background image

 Instruction manual 

GROW

BASE EC 

PRO

 

 

24

 

11

 

Technical data 

Dimensions (LxWxH) 

170mm x 100mm x 90mm 

Length of sensor cable (T/RH) 

ca. 5m 

Length of mains cables 

ca. 1.4m 

Power supply 1 

100-240V~ 10A 50-60Hz 

Power supply 2 (for “Multifunctional Out 4“) 

100-240V~ 10A 50-60Hz 

Maximum power per output “Multifunctional Out 1, 
2, 3“ 

1200W@230V 630W@120V 

Maximum power “Multifunctional Out 1+2+3“ 

2300W@230V 1200W@120V 

Maximum power “Multifunctional Out 4“ 

2300W@230V 1200W@120V 

International protection marking/Protection class 

IP42/ 

Repetitive sensor accuracy T/RH 

±0.1%RH/±0.2°C 

Absolute sensor accuracy 

±3%RH/±0.2°C 

Allowed ambient temperature 

10-40°C 

Table 4 

12

 

Disposal 

Observe the local regulations for material disposal. Dispose of the device in accordance with EC 
Directive 2002/96/EC –  WEEE (Waste Electrical and Electronic Equipment). If you have any 
questions, please contact the local authorities responsible for waste disposal. 

 

13

 

Service 

GrowControl wants to provide you the best level of service. To contact the customer service, 
please send an email to 

[email protected]

 

Summary of Contents for GROWBASE EC PRO


























Reviews: