1
English
Application
Operation is possible in conjunction with:
- Pressurized storage heaters
Operation with low-pressure storage heaters (displacement
water heaters) is
not
possible.
Specifications
• Max. flow
- Spout
approx. 29 L/min or 7.7 gpm
- Handspray
max. 9.5 L/min or 2.5 gpm
• Flow pressure
- min. 7.25
psi
- recommended
14.5 - 72.5 psi
- greater than 72.5 psi, fit pressure reducing valves
• Max. operating pressure
145 psi
• Test pressure
232 psi
• Temperature
- max. (hot water inlet)
176
°
F
• Water connection
cold on right side
hot on left side
Notes
- Installation of backflow protection must comply with local
codes and regulations.
- An access panel must be provided for access to diverter and
hose connections.
- Major pressure differences between hot and cold water
supply should be avoided.
Installation
Layout dimensions to establish centers and proper clearences,
see dimensional drawings on fold-out page I.
The dimensional drawing and the drilling template for fitting
plate (A) (not included in the scope of deliver) show a form of
installation suggested by
GROHE
, for which no further
components are required, see fold-out page I.
For deviation to the suggested installation, observe minimum
clearance required for escutcheon sizes.
Prepare
fitting plate
(A).
Install
thermostat unit,
see Figs. [1], [2] and [3].
1. Fasten mounting plate (B) to fitting plate (A) centrally, from
below using screws (C), see Fig. [1].
2. Attach pre-mounted thermostat unit (D) to the fitting plate
from above using bolts (E), see Fig. [2].
3. Secure 2 diagonally-opposed screws (E) from below using
cap nuts (F).
By loosening the screws (E), the thermostat unit can be
moved to the right and to the left, in order to enable opening
and closing of the isolating valves following installation or for
maintenance purposes.
4. Connect hoses (G) with G1/2 to the thermostat unit.
5. Attach sleeve (H), see Fig. [3].
6. Grease seal (J1) of escutcheon mounting base (J2) with the
special grease supplied.
7. Attach the escutcheon mounting base (J2) to the fitting and
fasten with mounting set (J3).
8. Attach escutcheon (J).
9. Install thermostat handle (K), snap insert (L) and screw (M).
The thermostat is adjusted at the factory. If, due to
installation conditions, re-adjustment is necessary, please
see
Adjustment
.
Install side valve,
see Figs. [3] and [4].
1. Install mounting and sealing set (N1) on the side valve
shank.
2. Fasten the side valve from above using mounting and
sealing set (N2).
The distance from the side valve upper edge to fitting
plate (A) must be 5/16" - 7/16", see Fig. [4].
3. Attach escutcheon (O).
4. Attach spindle & sleeve (P).
5. Connect hose (G) to the side valve with G3/4 and to the
thermostat unit with G1/2.
Install
diverter,
see Fig. [4] and fold-out page II, Fig. [5].
1. Install mounting and sealing set (T1) on the diverter shank,
see Fig. [5].
2. Fasten the diverter housing from above using mounting and
sealing set (T2).
The distance from the diverter housing upper edge to fitting
plate (A) must be 5/16" - 7/16" , see Fig. [4].
3. Attach spindle (U), see Fig. [5].
The distance from spindle (U) upper edge to fitting plate (A)
must be 2" . Fasten adjusted spindle (U) using set
screw (U1).
4. Attach escutcheon (V).
5. Install escutcheon hold down (W).
6. Install diverter knob (X).
7. Attach hose (Y) to the side valve and to the diverter.
8. Attach hoses (Y1) and (Y2).
Install
handspray,
see Fig. [6].
1. Attach hose guide (Z) to fitting plate (A) using mounting and
sealing set (Z1).
2. Install spray hose (B1) with hose (Y1).
Avoid crossing the hoses.
3. Insert spray hose (B1) through hose guide (Z).
4. Attach tapered nut (D1) to spray hose (B1).
5. Insert seal (E1) in the handshower adaptor (D1). Attach
handspray (F1) to the handshower adaptor.
When using the handspray (F1), it must be ensured that spray
water does not penetrate the hose guide (Z).
Install
spout,
see Fig. [7].
1. Install shank with sealing set (G1).
2. Attach hose (Y2) between spout and diverter.
3. Attach spout (J1) to the shank and insert set screw (K1)
using a 4mm allen wrench.
Flush pipes thoroughly.
Attach hoses (G) to the existing connections, see Fig. [8].
Cold water connection on right, hot water connection on
left.
Observe marking on the housing.
Check all connections for leaks
