1
English
Application
In order to ensure correct operation, a pressure of at least 21.75 psi is
necessary at the shower system.
Caution:
With sufficient power (from 18 kW) electric or gas instantaneous heaters
are also suitable.
All thermostats are adjusted in the factory at a flow pressure on both sides
of 45 psi.
Should temperature deviations exist due to special installation conditions,
the thermostat must be adjusted to the local conditions (see Adjustment).
Specifications
Minimum flow pressure
21.75 psi
Max. working pressure
145 psi
Recommended flow pressure
29.0 - 72.5 psi
Test pressure
232 psi
Flow rate at 3 bar flow pressure
Hand spray
max. flow 9,5 L/min or 2,5 gpm/ 80 psi
Side showers
max. flow 9,5 L/min or 2,5 gpm/ 80 psi
Handspray and side sprays
max. flow 9,5 L/min or 2,5 gpm/ 80 psi
Max. water temperature at hot water inlet
176 °F
Recommended max. flow temperature
(energy saving)
140 °F
Safety check
100 °F
Hot water temperature at supply connection min. 4 °F higher than mixed
water temperature
Cold water connection
right
Hot water connection
left
If static pressure is greater than 72.5 psi, fit pressure reducer.
Tools required,
see fold-out page I.
Delivery specification,
see fold-out page II.
Installation
New installation:
Make up unions.
For union dimensions for cold and hot water connection, see fold-out
page III Fig. [1].
The cold water supply must be connected on the right and the hot water
supply on the left.
The installation dimensions of the fitting relate to the standing level of the
shower stand, see Fig. [2].
The installation height of the showers from the standing level must be
observed in order to comfortably operate the fitting.
Retrofitting:
Union dimensions must correspond to Fig. [3].
The cold water supply must be connected on the right and the hot water
supply on the left.
The installation dimensions of the fitting relate to the standing level of the
shower stand, see Fig. [4].
The installation height of the showers from the standing level must be
observed in order to comfortably operate the fitting.
Connections and fastenings,
see fold-out page III and IV, Figs. [1]
to [10].
For individual components, see delivery specification, Figs. [I] to [IV].
1.Drill fixing holes for ø 8mm mounting plugs, see Fig. [1] and [3].
2.Install accompanying elbow unions (A). If S-unions are present, remove
and replace with elbow unions (A), see Fig. [5].
3.Screw in threaded studs (A1) into the elbow unions (A) using roughly
one turn.
Seal the elbow unions (A) at the tiled wall with sealing compound.
Flush pipes thoroughly
4.
Remove retaining rings (B) with installation tool (B1),
see Fig. [6].
5.
Detach wall plate (B2).
6.
Insert mounting plug (C1), see Fig. [7].
7.
Guide elbow unions (A) through the area provided in the fitting
assembly (C) and slide rib (A2) from below behind the lug (A3) of the
elbow union, see Fig. [8].
8.
Preassemble the fitting assembly (C) with the threaded studs (A1).
9.
Secure fitting assembly (C) using fixings (C2) supplied, see Fig. [7].
10. Connect hoses (D) with accompanying seals (D1) and elbow
unions (A), see Fig. [9].
Spray hose, shower rail slider, shower rail and hand spray,
see fold-
out page IV and V, Fig. [9], [10] and [11].
For individual components, see delivery specification, Figs. [IV], [V], [VI]
and [VII].
1.Attach spray hose (E) with seal (E1) to elbow unions (E2), see Fig. [9].
2.Slide shower rail slider (F) onto shower rail (F1), see Fig. [10].
3.Insert shower rail (F1) into the fitting assembly (C) and secure using
screw (F2).
4.Insert bracket (F3) onto the shower rail (F1) and secure using
screw (F4).
5.Fit cap (F5).
If there is an offset, wall plate 45 406 special accessory can be ordered.
6.Fit handspray (G) to spray hose (E), see fold-out page V, Fig. [11].
Attach wall plate (B2).
1.Insert seals (B4) into the wall plate (B2), note position of seal, see detail
view in Fig. [12].
2.Slide wall plate (B2) onto the fitting assembly (C), screw on retaining
rings (B) and tighten using installation tool (B1).
Note: Keep installation tool (B1) for possible future maintenance work
on the shower system.
3.Attach rosettes (B3) to the side sprays.
Adjustment
Temperature adjustment,
see Figs. [13] and [14].
• Before the mixer is put into service if the mixed water temperature
measured at the point of discharge varies from the specified
temperature set on the thermostat.
• After any maintenance operation on the thermostatic cartridge.
Operation of the
shut-off knob
(H), see Fig. [13]:
Flow-control knob in central position
= closed
Flow-control knob clockwise
= discharge from hand spray
Press button (H1) and turn
shut-off knob anti-clockwise
= discharge from side shower
Press button (H1) and turn
shut-off knob anti-clockwise fully
= discharge from side shower
and hand spray
1.Open cold and hot water supplies.
2.Open the shut-off knob (H) to the hand spray position and measure the
temperature of the running water using a thermometer.
3.Turn the temperature control handle (J) until the water temperature
reaches 38 °C.
4.Lever out cap (J1), see Fig. [14].
5.Hold thermostat knob (J) in this position and remove screw (J2).
6.Pull off thermostat knob (J) and reinstall in such a way that the 38 °C
mark on the wall plate (B2) coincides with the mark on the knob.
7.Reinstall screw (J2) and refit cap (J1).
Please pass these instructions on to the user of the fitting.
The right to make technical modifications is reserved.
Summary of Contents for 27 016
Page 7: ...VII VIII...
Page 8: ......