background image

 

OM/SM-BPM-E CE

IMPORTANT — READ FIRST — IMPORTANT

THESE APPLIANCES MUST BE INSTALLED BY A COMPETENT PERSON IN CONFORMITY WITH THE

INSTALLATION AND SERVICING INSTRUCTIONS AND NATIONAL REGULATIONS IN FORCE AT THE TIME.

PARTICULAR ATTENTION MUST BE PAID TO THE FOLLOWING:

I. E. E. REGULATIONS FOR ELECTRICAL INSTALLATIONS
ELECTRICITY AT WORK REGULATIONS
HEALTH AND SAFETY AT WORK ACT
FIRE PRECAUTIONS ACT
LOCAL AND NATIONAL BUILDING REGULATIONS

USERS SHOULD BE CONVERSANT WITH APPROPRIATE PROVISIONS OF THE FIRE PRECAUTIONS

ACT.  IN PARTICULAR THEY SHOULD BE AWARE OF THE NEED FOR REGULAR SERVICING BY A

COMPETENT PERSON TO ENSURE CONTINUED SAFE AND EFFICIENT APPLIANCE PERFORMANCE.
WARNING:

TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR ELECTRIC, MUST BE

EARTHED.  FAILURE TO EARTH BRAISING PAN COULD RESULT IN ELECTROCUTION 

AND DEATH.

ON COMPLETION OF THE INSTALLATION, THESE INSTRUCTIONS SHOULD BE LEFT WITH THE

ENGINEER-IN-CHARGE FOR REFERENCE DURING SERVICING.  FURTHER TO THIS, THE USERS

INSTRUCTIONS SHOULD BE HANDED TO THE USERS AND THE INSTALLER SHOULD INSTRUCT THE

RESPONSIBLE PERSON(S) IN THE CORRECT OPERATION AND MAINTENANCE OF THE APPLIANCE.
THIS EQUIPMENT IS ONLY FOR PROFESSIONAL USE AND SHALL BE OPERATED BY QUALIFIED

PERSONS.  IT IS THE RESPONSIBILITY OF THE SUPERVISOR OR EQUIVALENT TO ENSURE THAT USERS

WEAR PROTECTIVE CLOTHING, AND TO DRAW ATTENTION TO THE FACT THAT SOME PARTS WILL, BY

NECESSITY, BECOME VERY HOT AND WILL CAUSE BURNS IF TOUCHED ACCIDENTALLY.
UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER ARE 

NOT TO BE ADJUSTED BY THE INSTALLER.

CAUTION:

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.

WARNING 

:BEFORE ATTEMPTING ANY SERVICING, ENSURE THAT THE ELECTRICAL SUPPLY IS 

DISCONNECTED.

WARNING:

TO AVOID DAMAGE OR INJURY, FOLLOW THE WIRING DIAGRAM EXACTLY WHEN

CONNECTING A BRAISING PAN.

WARNING:

BEFORE CLEANING THE OUTSIDE OF THE BRAISING PAN, DISCONNECT ELECTRIC POWER.

KEEP WATER AND SOLUTIONS OUT OF CONTROLS AND ELECTRICAL COMPONENTS.

NEVER USE A HIGH PRESSURE HOSE TO CLEAN THE BRAISING PAN.

NOTICE:

DO NOT USE ANY DE-GREASER THAT CONTAINS POTASSIUM HYDROXIDE OR SODIUM

HYDROXIDE OR THAT IS ALKALINE.

WARNING:

HIGH VOLTAGE EXISTS INSIDE CONTROL COMPARTMENTS.  DISCONNECT FROM BRANCH

BEFORE SERVICING.  FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH.

WARNING:

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY GROEN OR

THEIR AUTHORIZED DISTRIBUTOR VOIDS ALL WARRANTIES AND CAN RESULT IN

BODILY INJURY TO THE OPERATOR AND DAMAGE THE EQUIPMENT.  SERVICE BY OTHER

THAN FACTORY-AUTHORIZED PERSONNEL WILL VOID ALL WARRANTIES.

CAUTION:

BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE OPERATING 

INSTRUCTIONS, CAUTIONS AND SAFETY INSTRUCTIONS CONTAINED N THIS MANUAL.

WARNING:

THIS BRAISING PAN IS INTENDED FOR USE IN THE COMMERCIAL HEATING, COOKING AND 

HOLDING OF WATER AND FOOD PRODUCTS, PER THE INSTRUCTIONS CONTAINED IN 

THIS MANUAL.  ANY OTHER USE COULD RESULT IN SERIOUS PERSONAL INJURY OR

DAMAGE TO THE EQUIPMENT AND WILL VOID WARRANTY.

Summary of Contents for ECLIPSE BPM-30CE

































Reviews: