background image

H7604 2000 Lb. Electric Winch

-

10

-

This winch has a pulling capacity of 2,000 
lbs.  Applying  this  capability  to  a  practical 
sense, you can:

•  Move a load from a “dead” stop of up to 

2,000 lbs. on level ground.

•  Move up to a 4,800 lb boat in water.
•  Maintain movement of a wheeled vehi-

cle of up to 6,000 lbs.

Pulling  capacity  is  reduced  as  the  incline 
increases. For example, maintaining vehi-
cle  movement  capacity  is  reduced  from 
6,000  lbs.  on  flat  ground  to  1,100  lbs.  on 
a 45° incline. Please refer to 

Figure 4

 for 

estimated  pulling  capacity  (maintaining 
vehicle movement) on various inclines.

Figure 4.

 Pulling capacity chart.

Pulling Capacity

Receiver Hitch

SECTION 3: Operations

To use the receiver hitch:

1.

  Turn  the  tow  vehicle 

OFF

  and  engage 

the parking brake.

2.

  Slide a draw bar with a hitch ball into the 

receiver and secure it with a hitch pin.

3.

  Connect the trailer to the hitch ball and 

attach the safety chains to the receiver 
hitch.

To use the hand crank:

1.

  Turn the clutch knob clockwise until it is 

hand tight. Do not force or overtighten.

Hand Crank

2.

  Remove the outer hex nut and place the 

end of the hand crank over the flattened 
end  of  the  threaded  shaft  (see 

Figure 

5

).

3.

  Replace the outer hex nut and tighten it 

against the hand crank.

4.

  Rotate  the  hand  crank  clockwise  to 

tighten  the  cable.  Turn  until  the  cable 
has been completely retracted.

Figure 5.

 Hand crank.

Summary of Contents for H7604

















Reviews: