Grizzly G0857, Owner'S Manual

Page: 63 / 65

-60-
Model G0857/G0858 (Mfd. Since 07/19)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
Labels & Cosmetics
WARNING!
INJURY HAZARD!
To reduce risk of short
and long-term injury,
wear safety glasses,
hearing protection, and
a respirator when using
this machine.
DANGER!
WARNING! WARNING!
Use this guard for all
possible operations, and
immediately reinstall it
following operations that
require its removal.
ROTATING
CUTTERHEAD BELOW!
KICKBACK HAZARD!
1. Ensure outfeed table is
even with knives/inserts.
2. Never exceed the
maximum depth of cut.
3. Do not stand directly
behind workpiece.
ALWAYS USE
PUSH BLOCKS!
Push blocks minimize the
possibility of operators
hands contacting the
cutterhead while cutting.
G0858
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
Cutterhead
exposed
between
these lines.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
Failure to keep hands clear
of cutterhead will result in
serious personal injury.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
KEEP PANEL
CLOSED
WHILE
OPERATING!
201
203 204
205
207
208
206
202
209
210
212
211
203
206
214
213
To reduce the risk of serious injury when using this machine:
1. Read and understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Except when rabbeting, keep all guards in place and in proper
operating condition. Always replace guard after rabbeting.
5. Never cut workpieces smaller than 10" long and 1/2" thick.
6. Always use push blocks when face planing.
7. Keep hands at least 4" away from cutterhead.
8. Never cut deeper than 1/8" on a single pass.
9. Be aware of "kickback" hazards and how to prevent them.
10. Turn motor OFF and disconnect power before changing inserts,
adjusting tables/fence, or servicing.
11. Tie back long hair, roll up sleeves, and DO NOT wear loose
clothing, gloves, or jewelry.
12. Before starting, ensure tables are adjusted properly, inserts are
secure, and jointer is stable.
13. Do not joint boards with cracks, loose knots, or any defects.
14. DO NOT expose to rain or use in wet locations.
15. Always support workpiece against fence and table when cutting.
Never attempt any operation free-handed.
16. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
17. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
Motor: 3 HP, 230V, Single-Phase, 60 Hz
Full-Load Current: 12A
Cutterhead: Helical w/Indexable Inserts
Insert Size: 15 x 15 x 2.5mm
Number of Inserts: 36
Replacement Inserts: H9893
Cutterhead Speed: 5500 RPM
Cuts Per Minute: 22,000
Fence Tilt: 45º, 90º, 135º
Table Size: 76" x 8"
Min. Workpiece Length: 10"
Min. Workpiece Thickness: 1/2"
Max. Depth of Cut Per Pass: 1/8"
Max. Rabbeting Depth: 1/2"
Weight: 365 lbs.
Specifications WARNING!
Mfd. for Grizzly in Taiwan
Date
S/N
MODEL G0858
8" X 76" PARALLELOGRAM JOINTER
w/HELICAL CUTTERHEAD & MOBILE BASE
175370
G0857
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
grizzly.com
To reduce the risk of serious injury when using this machine:
1. Read and understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Except when rabbeting, keep all guards in place and in proper
operating condition. Always replace guard after rabbeting.
5. Never cut workpieces smaller than 10" long and 1/2" thick.
6. Always use push blocks when face planing.
7. Keep hands at least 4" away from cutterhead.
8. Never cut deeper than 1/8" on a single pass.
9. Be aware of "kickback" hazards and how to prevent them.
10. Turn motor OFF and disconnect power before changing blades,
adjusting tables/fence, or servicing.
11. Tie back long hair, roll up sleeves, and DO NOT wear loose
clothing, gloves, or jewelry.
12. Before starting, ensure tables are adjusted properly, blades are
secure, and jointer is stable.
13. Do not joint boards with cracks, loose knots, or any defects.
14. DO NOT expose to rain or use in wet locations.
15. Always support workpiece against fence and table when cutting.
Never attempt any operation free-handed.
16. Always feed workpiece against cutterhead rotation. Never move
workpiece backward while feeding.
17. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
Motor: 3 HP, 230V, Single-Phase, 60 Hz
Full-Load Current: 12A
Cutterhead: 4-Knife, 3-1/16" Dia.
Knife Size: 8" x 3/4" x 1/8"
Replacement Knives: H4982
Cutterhead Speed: 5500 RPM
Cuts Per Minute: 22,000
Fence Tilt: 45º, 90º, 135º
Table Size: 76" x 8"
Min. Workpiece Length: 10"
Min. Workpiece Thickness: 1/2"
Max. Depth of Cut Per Pass: 1/8"
Max. Rabbeting Depth: 1/2"
Weight: 365 lbs.
Specifications WARNING!
Mfd. for Grizzly in Taiwan
Date
S/N
MODEL G0857
8" X 76" PARALLELOGRAM JOINTER
w/MOBILE BASE
175370
205
REF PART # DESCRIPTION REF PART # DESCRIPTION
201 P0857201 MACHINE ID LABEL (G0857) 208 P0857208 EYES EARS LUNGS WARNING LABEL
201 P0858201 MACHINE ID LABEL (G0858) 209 P0857209 MODEL NUMBER LABEL (G0857)
202 P0857202 READ MANUAL LABEL 209 P0858209 MODEL NUMBER LABEL (G0858)
203 P0857203 CUTTERHEAD WARNING LABEL 210 P0857210 GRIZZLY.COM LABEL
204 P0857204 CUTTERHEAD EXPOSED LABEL 211 P0857211 GRIZZLY NAMEPLATE-SMALL
205 P0857205 ELECTRICITY LABEL 212 P0857212 PANEL CLOSED WARNING LABEL
206 P0857206 DISCONNECT POWER LABEL 213 P0857213 TOUCH-UP PAINT, GRIZZLY GREEN
207 P0857207 CUTTERHEAD GUARD LABEL 214 P0857214 TOUCH-UP PAINT, GREY PUTTY
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.