Grizzly G0706, Owner'S Manual

Page: 28 / 60

"'+"
BdYZa<%,%+B[\#h^cXZ&&$%.
To rabbet cut on the jointer:
1. 9>H8DCC:8I?D>CI:G;GDBEDL:G
2. GZVYVcYjcYZghiVcY SECTION 1: SAFETY,
WZ\^cc^c\dc
Page 6
#
3.
BV`Z hjgZ ndjg hidX` ]Vh WZZc ^cheZXiZY
[dgYVc\ZgdjhXdcY^i^dchVhYZhXg^WZY^ci]Z
Stock Inspection & Requirements
^chigjX"
i^dch!WZ\^cc^c\dc Page 21 #
4. HZii]ZXjii^c\YZei][dgndjgdeZgVi^dc#LZ
gZXdbbZcY WZilZZc & ¿
&+
VcY & ¿
-
[dg gVWWZi
Xjii^c\#
When the cutterhead guard is removed,
attempting any other cut besides a rabbet
directly exposes the operator to the moving
cutterhead. Always replace the cutterhead
guard after rabbet cutting!
I]ZejgedhZd[gVWWZiXjii^c\^hidgZbdkZVhZX"
i^dcd[i]Zldg`e^ZXZZY\ZhZZ
Figures 31-32 #
L]ZcXdbW^cZYl^i]Vcdi]ZggVWWZi"XjiZY\Z!i]Z
gVWWZi_d^cihXgZViZVh^beaZ!nZihigdc\bZi]dYd[
_d^c^c\hidX`#
Figure 32.
>aajhigVi^dcd[gVWWZiXjii^c\Z[[ZXih
VcYV[ZlhVbeaZ_d^cih#
Figure 31.
Ine^XVagVWWZiXjii^c\deZgVi^dc#
Rabbet Cutting
NOTICE
If you are not experienced with a jointer,
set the depth of cut to 0", and practice
feeding the workpiece across the tables as
described below. This procedure will better
prepare you for the actual operation.
5.
GZbdkZi]ZXjiiZg]ZVY\jVgY#
6.
HZi i]Z [ZcXZ id .%•! i]Zc bdkZ ^i [dglVgY
hdi]ZVbdjcid[XjiiZg]ZVYZmedhZY^hi]Z
hVbZVhi]Zh^oZd[ndjggVWWZi
7.
8dccZXii]Z_d^ciZgidedlZgVcYijgc^i
ON
#
8.
L^i] V ejh] WadX` ^c ZVX] ]VcY! egZhh i]Z
ldg`e^ZXZ V\V^chi i]Z iVWaZ VcY [ZcXZ l^i]
[^gb egZhhjgZ! VcY [ZZY i]Z ldg`e^ZXZ dkZg
i]ZXjiiZg]ZVY#
Note
/
If your leading hand gets within 4" of the
cutterhead, lift it up and over the cutterhead,
and place the push block on the portion of the
workpiece that is on the outfeed table. Now,
focus your pressure on the outfeed end of
the workpiece while feeding, and repeat the
same action with your trailing hand when it
gets within 4" of the cutterhead. To keep your
hands safe, DO NOT let them get closer than
4" from the cutterhead when it is moving!
9. GZeZVi Step 8 jci^ai]ZndjggVWWZi^hXjiid
YZei]#