Grizzly G0670, Owner'S Manual

Page: 21 / 116

<%+,%&+m)%=^\]EgZX^h^dc:KHAVi]Z
"&."
Test Run
DcXZ ndj ]VkZ gZVY i]^h bVcjVa VcY iV`Zc Vaa
hV[ZinegZXVji^dch!ndjVgZgZVYnidXdbeaZiZi]^h
iZhigjc#>[!Yjg^c\i]ZiZhigjc!ndjXVccdiZVh^an
adXViZi]ZhdjgXZd[VcjcjhjVacd^hZdgk^WgVi^dc!
hide gjcc^c\ i]Z bVX]^cZ ^bbZY^ViZan! VcY gZ[Zg
Troubleshooting
dc
Page 59
[dgVhdaji^dc#
>[ndjhi^aaXVccdigZbZYnVegdWaZb!XdciVXidjg
IZX]HjeedgiVi*,%*)+".++([dgVhh^hiVcXZ#
To test run the lathe:
1. 9>H8DCC:8II=:A6I=:;GDBEDL:G
2. BV`Z hjgZ i]Vi i]Z ]ZVYhidX` d^a iVc`!
\ZVgWdm! Vegdc! VcY aZVY hXgZl gZhZgkd^g d^a
aZkZah VgZ [jaa# GZ[Zg id
Lubrication ^c i]Z
MAINTENANCE
hZXi^dc dc
Page 53
d[ i]^h
bVcjVa[dgYZiV^ah#
3 # BV`ZhjgZi]Vii]ZX]jX`VcY_VlhVgZhZXjgZ
gZ[Zgid
Chuck and Faceplate Mounting
dc
Page 25 #
4 # Ijgci]Zejbehl^iX] Figure 11 idi]Z OFF
edh^i^dc! [^aa i]Z Xjii^c\ [aj^Y gZhZgkd^g gZ[Zg
id
Cutting Fluid System dc Page 58 ! VcY
ed^cii]Z[aj^YcdooaZ^cidi]ZX]^eeVc#
5
# Ijgci]Z8HHDC$D;;hl^iX]id
ON
!ijgci]Z
he^cYaZheZZYY^Va Figure 11 id^ihb^c^bjb
heZZY! VcY bV`Z hjgZ i]Z Xgdhh ha^YZ ^h
WVX`ZY dji id Vkd^Y edhh^W^a^in d[ V ]^\]"
heZZYhiVgi#
Note: With the CSS switch in the ON position
the spindle speed varies with the cross slide
position. With the switch in the OFF position,
the spindle speed is independent of the cross
slide position. Do not switch between modes
when the lathe is operating.
This lathe is shipped without oil. Fill all
gearboxes to the correct level, and oil the
ways and all lubrication points before start-
ing lathe. Ignoring this notice will result in
lathe damage and void warranty!
NOTICE
Figure 12. =ZVYhidX`gVc\ZaZkZg#
6
# GdX`i]ZX]jX`WVX`VcY[dgi]Wn]VcYVcY
bdkZi]Z]ZVYhidX`gVc\ZaZkZg
Figure 12
id i]Z aZ[i hd i]Z ]ZVYhidX` ^h ^c adl gVc\Z
'%")%%GEB#
Figure 11.
8dcigdaeVcZa#
He^cYaZHeZZY9^Va
8HHDC$D;;Hl^iX]
EjbeHl^iX]
:bZg\ZcXnHideHl^iX]
Figure 13.
<ZVgWdmgVc\ZaZkZg#
7
# BdkZi]Z<ZVgWdmgVc\ZaZkZgidcZjigVaVh
h]dlc^c Figure 13 #