background image

G0646/G0647  50/65 Ton Ironworker

-23-

4.

  Loosen  the  die  set  screws  on  both  sides  of 

the punch bolster, then lift the die from below 
and remove it (see 

Figure 20

).

5.

  Use  the  spanner  wrench  to  loosen  and 

remove the punch retaining ring, then sepa-
rate the punch adapter and die from the ring 
(see 

Figure 21

).

Figure 21.

 Punch assembly removed and 

separated.

Punch

Adapter

Retaining Ring

Figure 20.

 Punching die removed.

Punching Die

Set Screw

(1 of 2 shown)

Bolster

6.

  Thoroughly  clean  any  metal  debris  or  grime 

off  the  punch,  die,  pressure  plate,  and  bol-
ster.

 

Note: 

If  you  are  storing  the  punch  and 

die,  protect  them  with  a  light  coat  of  an 
anti-rust  product  like  G96®  Gun  Treatment, 
SLIPIT®, or Boeshield® T-9 (see 

Section 5: 

Accessories

 on 

Page 35

 for more details).

To install punch tooling:

1.

  Set the controls to 

Notch

 and 

Inch

, use the 

foot actuator to raise the punch to the upper-
most position, then stop the motor.

2.

  DISCONNECT MACHINE FROM POWER!

3.

  Move the stripper and safety guard assembly 

out of the way.

4.

  Thoroughly  clean  the  punch,  die,  pressure 

plate,  and  bolster,  then  re-lubricate  them  to 
prevent rust.

5.

  Place the adapter into the retaining ring, then 

the punch into the adapter (see 

Figure 21

).

6.

  Center  the  assembly  up  against  the  punch 

pressure plate, then hand-tighten the retain-
ing ring to secure it in place (see 

Figure 22

).

Figure 22.

 Punch, adapter, retaining ring, and 

die installed.

Die

Pressure

Plate

Punch

Assembly

NOTICE

To reduce the risk of tooling breakage, the 

recommended  side  clearance  between  the 

punch and die is approximately 10% of the 

material thickness.

Summary of Contents for 50/65 Ton Ironworker G0647













































































Reviews: