manualshive.com logo in svg

GridSense Line IQ LIQ60, User Manual, Page: 30 / 39

Share
Download
GridSense Line IQ LIQ60 User Manual Download Page 30

File: LIQ User Manual V2.0 

Page 28 of 37 

 

 

 

Appendix A

– LineMan

 

A.1 LineMan Overview

 

LineMan  is  a  software  package  supplied  by  GridSense  for  configuring  and  communicating  with  the 
LineIQ  suite  of  products.  It  is used  during  the  commissioning  phase  when  setting  up  an  LIQ-60  or  LIQ- 
Gateway, and subsequently when downloading information from the LIQ-60 or LIQ-Gateway to a PC. 

 

A.2 Setting up an LIQ-LocalLink

 

In order for a PC to communicate with an LIQ-60 or  an LIQ-Gateway, it needs to use short range radio. 
This is achieved by using an LIQ-LocalLink which is a radio modem that plugs into a USB slot on a  PC. 

The first time you use the LIQ-LocalLink on a PC, it needs to have the correct driver loaded. This driver 
forms  part  of  Windows  7,  so  the  LIQ-LocalLink  should  have  its  driver  automatically  loaded  when  it  is 
inserted into a USB slot. Section 3.1 will detail installation procedures for Window 7 whereas Appendix B 
details installation procedures for Windows  XP. 

If you are using Windows XP, you can install the driver off the CD containing LineMan: 

1.  From Windows Explorer, run the setup.exe. 

2.  Follow the instructions from Windows Install to install the driver. 

3.  Once the driver is installed you can run LineMan. 

 

A.3 Connecting to the CMS with LineMan

 

1.  Click on the 

Start → All Programs → GridSense → LineMan → LineMan 

to launch the 

LineMan application. 

2.  Select the correct COM port as indicated by the 

LineMan Connection Window 

and click  on 

Connect to Line Tracker

. 

 

 

 

Figure 8: COM port selection

 

3.  The available LIQ-60 within the RF range is displayed under the Line Tracker ID List, listed by 

their respective serial numbers.

Summary of Contents for Line IQ LIQ60








































Reviews:

No comments