GREMO 1050F4 Instruction Manual Download Page 76

Page: 76 / 198

5 User manual for GreControl control system

5.3 Main window

Gremo1050F4 Instruction manual

Low gear is indicated by

and high gear is indicated

. If the adjustable off-road mode is activated, a

green line is shown under the symbol. The percentage
is the current maximum value

• Bogie lift

Normally the bogie lift is in float mode which is indicated

with the green bogie symbol

. When the bogie is

locked, a red bogie symbol

is shown in the display.

One for each side

• Articulated joint lock

When the articulated joint lock is activated, a red

padlock

is displayed. An open green padlock

shown if the articulated joint lock is disconnected.

• Parking brake

A red

is displayed when the parking brake is

engaged.

5.3.2

Instrumentation

The centre area of the main window displays
instrumentation for the following from left to right:

Fig. 53 GreControl, instrument in main window

• The current speed (kph) of the machine.

• Current diesel engine speed (rpm).

NOTICE

The red line indicates the rpm limitation of the engine
when the hydraulics are below 15 degrees.

• Tank fuel volume where the red area indicates a low

fuel level in tank.

Summary of Contents for 1050F4







































































































































































































Search results

Summary of Contents for 1050F4

Reviews:

GREMO 1050F4, Instruction Manual, Page: 76 / 198

Search results

Summary of Contents for 1050F4

Reviews: