background image

clean, and free from oil and grease. Failure to do so can
cause serious injury.

Check damaged parts before using the appliance, a guard
or other part that is damaged should be carefully checked
to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, damaged
mountings, and any other condition that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.

Remove or disconnect battery before servicing, cleaning
or removing material from the gardening appliance.

Do not modify or attempt to repair the appliance or the
battery pack (as applicable) except as indicated in the
instructions for use and care. Use appliances only with
specifically designated battery packs. Use of any other
battery packs may create a risk of injury and fire. Use
only with Greenworks LB602, LB6025, LB603, LB604,
LB605, LB606 battery or other BAC series.

Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack. Use only with Greenworks
CAC801, CH60DP01, 60DPC10A, CH60R00 charger or
other CAC series.

When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery
terminals together may cause a fire.

Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.

Do not use a battery pack or appliance that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk
of injury.

Do not expose a battery pack or appliance to fire or
excessive temperature. Exposure to fire or temperature
above 265 °F (130 °C) may cause an explosion.

Do not dispose of the batteries in a fire. The cells may
explode. Check with local codes for possible special
disposal instructions.

Do not open or mutilate the batteries. Released electrolyte
is corrosive and may cause damage to the eyes or skin. It
may be toxic if swallowed.

Exercise care in handling batteries in order not to short
the battery with conducting materials such as rings,
bracelets, and keys. The battery or conductor may
overheat and cause burns.

Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature range
specified in the instructions. Charging improperly or at
temperatures outside of the specified range may damage
the battery and increase the risk of fire.

Have servicing performed by a qualified repair person
using only identical replacement parts. This will ensure
that the safety of the product is maintained.

Keep guards in place and in working order.

Keep hands and feet away from cutting area.

Disconnect the battery pack from the appliance before
making any adjustments, changing accessories, or storing
appliance. Such preventive safety measures reduce the
risk of starting the appliance accidentally.

Use only with the nylon cutting line of 0.095" / 0.080"
(2.4 mm / 2.0 mm) diameter. Do not use heavier lines
than recommended by the manufacturer and line
materials of other types – for example, metal wire, rope,
and the like.

SAVE THESE INSTRUCTIONS

3

SYMBOLS ON THE MACHINE

Some of the following symbols can be used on this machine.
Please study them and learn their definition. Proper
interpretation of these symbols will let you operate the tool
better and safer.

Symbol

Explanation

V

Voltage

A

Current

Hz

Frequency (cycles per second)

W

Power

min

Time

/min

Revolutions, strokes, surface speed, or-
bits etc., per minute

Direct current

Precautions that involve your safety.

Read and understand all instructions be-
fore you operate the machine, and follow
all warnings and safety instructions.

Always wear safety glasses with side
shields marked to comply with ANSI
Z87.1 when you operate this machine.

Do not expose the machine to rain or
moist conditions.

Keep all bystanders at least 15m away.

Do not install or use any type of blade on
the machine or displaying this symbol.

Thrown objects can ricochet and result in
personal injury or property damage.

5

English

EN

Summary of Contents for ULTRAPOWER 60V ST60L04

































Reviews: