background image

1

DESCRIPTION

1.1

PURPOSE

This machine is used to remove and clear away snow from

pavements, gardens, driveways and other ground-level

surfaces.

1.2

OVERVIEW

1

Bail lever

2

Upper handle

3

Middle handle

4

Lower handle

5

Cam lock

6

Battery door

7

Scraper

8

Impeller

9

Discharge chute

10

Chute deflector

11

Chute-rotation handle

1.3

PACKING LIST

1

Snow thrower bare

tool

2

Chute deflector

assembly

3

Quick-release lever

assembly

4

Chute-rotation box

assembly

5

Upper handle

assembly

6

Middle handle

assembly

7

Manual

2

GENERAL POWER TOOL

SAFETY WARNINGS

 

WARNING

Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your battery-

operated (cordless) power tool.

2.1

TRAINING

• Do not allow children under the age of 14 to operate this

tool. Children who are 14 years of age or older must read

and understand the operating instructions and safety rules

in this manual and must be trained and supervised by a

parent.

• Read the operating and service instruction manual

carefully. Be thoroughly familiar with the controls and

the proper use of the power tool. Know how to stop the

unit and disengage the controls quickly.

• Never allow children to operate the power tool. Never

allow adults to operate the power tool without proper

instruction.

• Keep the area of operation clear of all persons,

particularly small children, and pets.

• Exercise caution to avoid slipping or falling, especially

when operating in reverse.

• Do not use on graveled surfaces.
• Dress Properly – Do not wear loose clothing or jewelry.

They can be caught in moving parts.

• Wear appropriate boots when operating the snow thrower.
• Operation of the snow thrower in the hand-held position

is unsafe, except in accordance with the special

instructions for such use provided in the operator’s

manual.

2.2

PREPARATION

• Thoroughly inspect the area where the power tool is to be

used and remove all doormats, sleds, boards, wires, and

other foreign objects.

• Do not operate the power tool without wearing adequate

winter garments. Wear footwear, which will improve

footing on slippery surfaces.

• Adjust the housing height to clear gravel or crushed rock

surface.

• Never attempt to make any adjustments while the

machine is running (except where specifically

recommended by manufacturer).

• Always wear safety glasses or eye shields during

operation or while performing an adjustment or repair to

protect eyes from foreign objects that may be thrown

from the machine.

• Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to battery pack, picking up

or carrying the appliance. Carrying the appliance with

your finger on the switch or energizing appliance that

have the switch on invites accidents.

• Disconnect the battery pack from the appliance before

making any adjustments, changing accessories, or storing

appliance. Such preventive safety measures reduce the

risk of starting the appliance accidentally.

2

English

EN

Summary of Contents for 2608402CO















Reviews: