GreenWorks Commercial 82TB16 Operator'S Manual Download Page 3

1

DESCRIPTION

1.1

PURPOSE

This machine is used to cut grass, light weeds, and

other similar vegetation at or around ground level. The

cutting plane must be approximately parallel to the

ground surface. You cannot use the machine to cut or

chop hedges, shrubs, bushes, flowers and compost.

1.2

OVERVIEW

1

2

4

3

9

10

11

5

6

7

8

-

+

+

1

Battery release button

2

Carrying strip

3

Trigger

4

Auxiliary handle

5

Speed button/lock-out button

6

On/off button

7

LED indication

8

Reverse button

9

Shaft

10

Guard

11

Cut-off blade

12

Blade

2

IMPORTANT SAFETY

INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING (THIS

POWER TOOL)

 

WARNING

Read and understand all instructions before using this

product. Failure to follow all instructions listed below

may result in electric shock, fire, and/or serious

personal injury.

• Use only identical manufacturer’s replacement parts

and accessories. Use of any other parts may create

a hazard or cause product damage.

• Always wear safety glasses with side shields

marked to comply with ANSI Z87.1. Everyday

glasses have only impact resistant lenses. They are

NOT safety glasses. Following this rule will reduce

the risk of eye injury. Use face mask if operating in

dusty work spaces.

• Avoid Dangerous Environment – Don’t expose

power tools to damp or wet conditions. Water

entering a power tool will increase the risk of electric

shock.

• Don’t use in rain.
• Keep all bystanders, children, and pets at least 50 ft.

away.

• Dress Properly – Do not wear loose clothing or

jewelry. They can be caught in moving parts. Use of

rubber gloves and substantial footwear is

recommended when working outdoors. Wear

protective hair covering to contain long hair.

• Use right Appliance. Do not use appliance for any

job except that for which it is intended.

• Avoid Unintentional Starting – Don’t carry appliance

with finger on switch. Be sure switch is off when

battery is plugged in.

• Don’t Force Appliance – It will do the job better and

with less likelihood of a risk of injury at the rate for

which it was designed.

• Don’t overreach – Keep proper footing and balance

at all times.

• Stay alert – Watch what you are doing. Use

common sense. Do not operate this unit when you

are tired, ill or under the influence of alcohol, drugs

or medication.

• Always store idle power tools indoors – When not in

use, power tools should be stored indoors in a dry

and high or locked-up place, out of reach of

children.

• Maintain Appliance With Care – Replace string head

if cracked, chipped, or damaged in any way. Be sure

the string head is properly installed and securely

fastened. Keep cutting edge sharp and clean for

best performance and to reduce the risk of injury.

Follow instructions for lubricating and changing

2

English

EN

Summary of Contents for 82TB16















Reviews: