manualshive.com logo in svg

Greenlee 39693, Operation, Service And Parts Instruction Manual, Page: 2 / 20

Share
Download
Greenlee 39693 Operation, Service And Parts Instruction Manual Download Page 2

2

Greenlee Textron / Subsidiary of Textron Inc.

4455 Boeing Dr., Rockford, IL 61109-2988    815/397-7070

Bus Bar Punch System

Table of Contents

Additional copies of this manual are available upon request at no charge.

A person who has not read and does not understand all
operating instructions is not qualified to operate this tool.

Failure to read and understand safety instructions may
result in injury or death.

Introduction and Purpose of this Manual .............................................................. 2
Safety Information ................................................................................................. 3
Specifications and Capacity ................................................................................. 4
Description ............................................................................................................ 4
Setup ................................................................................................................. 5-6
Operation .............................................................................................................. 7
Punch, Die and Stripper Plate Selection .............................................................. 9
Troubleshooting .................................................................................................. 10
Ram Unit ............................................................................................................. 11
Yoke Pin .............................................................................................................. 12
Alignment Table .................................................................................................. 13
X-Y Table (optional) ............................................................................................ 14

Mounting the X-Y Table to the Bus Bar Punch Unit ...................................... 14

Punch Unit

Disassembly / Assembly ................................................................................ 15
Exploded View ............................................................................................... 16
Parts List ........................................................................................................ 17

Introduction

The Greenlee 39693 Bus Bar Punch with Table consists
of a punch unit, hydraulic ram, and an alignment table.
The 39693 is intended to punch copper or aluminum
bus bar up to 12mm x 120mm. Two separate die sets
are furnished with the punch unit - one set for laminated
bus bar and one set for solid bus bar.

The 39693 is intended to be used with any Greenlee
hydraulic pump capable of developing 10,000 psi
(690 BAR), such as:

Manual Pump: 755

Electric Pump (120-volt): 960, 975, 980

Electric Pump (220-volt): 976-22 FS, 976-22-PS,

980-22 FS, 980-22 PS

An optional X-Y Punch Table (catalog number 37736) is
available for repetitious punching of standard 2-bolt and
4-bolt hole patterns.

Purpose of this Manual

This instruction manual is intended to familiarize
operating and maintenance personnel with the safe
operation and maintenance procedures associated with
the 39693 Bus Bar Punch with Table.

Summary of Contents for 39693





















Reviews:

No comments