E.
Pipe the drain line
Again be sure not to trap water. If necessary employ a condensate pump/drain to
elevate the drain water and evacuate it during drain cycles.
II) RO System Location and Piping:
A. Now install the Reverse
mountable with simply two screws and can be hung as self supporting. Follow
the instructions outlined below
respective connections. All connections are simple quick connec
recommended that a shut off valve be placed in line after tapping the domestic
water line for the RO System supply.
1) Locate and connect the
equipment. This will be the right side as you face the system. The
supply side will consist of Black ¼” tubing.
2) Locate the Yellow drain line, and place in an appropriate area for
drainage.
HUMIDIFICATION SEASON IS MONTHS AWAY.
CONDENSATE PUMP
3) Locate the b
humidifiers
system metal frame)
storage tank.
proximity to the RO System.
4)
Make sure to open the valve at the top of the storage tank.
5) Once installed, allow the system to run for approximately 15
minutes to flush completely. Make sure there are no leaks, parts
can come loose in shippin
6) The RO System will run until all the humidifier supply lines and
storage tank are filled and charged to the pressure of the building.
This may take several hours to happen.
7) PLEASE N
WATER SUPPLY TO THE RO SYSTEM.
if this is a problem)
B. Pipe supply piping from
Panel/Generator or STS Box
C. Open the inline water valve off of the build
the filling of water to the
filling the clear water filter housings on the RO System.
D. Check for leaks. As stated above The RO System will run until all the humidifier
supply lines and storage tank are filled and charged to the pressure of the
building. This may take several hours to happen. Again, make sure that the
drain is working – if the drain line is fed to a condensate pump the pump MUST
BE OPERABLE! The RO System h
Pipe the drain line from the Control Panel to an appropriate drain location.
Again be sure not to trap water. If necessary employ a condensate pump/drain to
elevate the drain water and evacuate it during drain cycles.
II) RO System Location and Piping:
everse Osmosis (RO) Water system. These systems are wall
mountable with simply two screws and can be hung as self supporting. Follow
outlined below for connecting the colored tubes to their
respective connections. All connections are simple quick connec
recommended that a shut off valve be placed in line after tapping the domestic
water line for the RO System supply.
Locate and connect the domestic water supply side of the
quipment. This will be the right side as you face the system. The
ply side will consist of Black ¼” tubing.
Locate the Yellow drain line, and place in an appropriate area for
drainage.
NOTE: DRAIN MUST BE OPERABLE! EVEN IF THE
HUMIDIFICATION SEASON IS MONTHS AWAY.
CONDENSATE PUMP – IT MUST BE ON LINE!
Locate the blue product water line that will provide
humidifiers. Utilize a “t” connector (provided and taped to the RO
system metal frame) to hook up the product water (blue line) to the
storage tank. Locate the 2.5 gallon storage/bladder
proximity to the RO System.
Make sure to open the valve at the top of the storage tank.
Once installed, allow the system to run for approximately 15
minutes to flush completely. Make sure there are no leaks, parts
can come loose in shipping. Hand tightening may be necessary.
The RO System will run until all the humidifier supply lines and
storage tank are filled and charged to the pressure of the building.
This may take several hours to happen.
PLEASE NOTE: 35 PSI MINIMUM REQUIRED ON INCO
WATER SUPPLY TO THE RO SYSTEM.
(Consult with the Factory
if this is a problem)
Pipe supply piping from the RO System to the fitting on the side of the
or STS Box labeled “
water in
”.
Open the inline water valve off of the building domestic water supply to begin
filling of water to the RO System. You should notice water immediately
filling the clear water filter housings on the RO System.
As stated above The RO System will run until all the humidifier
lines and storage tank are filled and charged to the pressure of the
building. This may take several hours to happen. Again, make sure that the
if the drain line is fed to a condensate pump the pump MUST
The RO System has an automatic shut off valve (ASO) that
3
to an appropriate drain location.
Again be sure not to trap water. If necessary employ a condensate pump/drain to
Water system. These systems are wall
mountable with simply two screws and can be hung as self supporting. Follow
for connecting the colored tubes to their
respective connections. All connections are simple quick connects. It is
recommended that a shut off valve be placed in line after tapping the domestic
supply side of the
quipment. This will be the right side as you face the system. The
Locate the Yellow drain line, and place in an appropriate area for
NOTE: DRAIN MUST BE OPERABLE! EVEN IF THE
IF PIPED TO A
e product water line that will provide RO water to the
(provided and taped to the RO
to hook up the product water (blue line) to the
Locate the 2.5 gallon storage/bladder tank in close
Make sure to open the valve at the top of the storage tank.
Once installed, allow the system to run for approximately 15
minutes to flush completely. Make sure there are no leaks, parts
g. Hand tightening may be necessary.
The RO System will run until all the humidifier supply lines and
storage tank are filled and charged to the pressure of the building.
OTE: 35 PSI MINIMUM REQUIRED ON INCOMING
(Consult with the Factory
the RO System to the fitting on the side of the Control
ing domestic water supply to begin
System. You should notice water immediately
As stated above The RO System will run until all the humidifier
lines and storage tank are filled and charged to the pressure of the
building. This may take several hours to happen. Again, make sure that the
if the drain line is fed to a condensate pump the pump MUST
as an automatic shut off valve (ASO) that