background image

Gree                                                                            VRF Protocol Gateway 

Remarks

1

 

One 485 bus can connect to 254 gateways at most, if there a re other 485 equipment 

in the 485 bus, the connectable gateway should reduce accordingly. 

2

 

It is recommended that the connecting quantity of gateway of 485 bus n is less or 

equal to 16. 

2 Introduction to Parts 

2.1 Parts List 

S=standard fittings; O=prepared by user; P=purchased by user 

Name 

Model 

Material Code 

Remarks 

Supply Range 

VRF Protocol 

Gateway kit 

Gateway components 

ME30-24/D1(BM) 

NC20000160 

 

Can connect to BMS 

 

Protocol interfaces: Modbus 
protocol, CAN protocol, 
BACnet protocol 

 

Hardware interface: RS485, 
CAN, Ethernet 

 

485 communication baud rate 
9600, start bit 1 bit, data bit 8 
bits, no parity bit, stop bit 1 bit 

 

TCP communication: 
gateway Modbus TCP fixed 
interface: 502 

 

UDP port in BACnet/IP mode: 
BAC0 

 

Major components: gateway, 
instruction manual 

Optical isolation 

relay 

Optical isolation relay   

RS485 

LN02200010 

The total distance of the 

communication cable needs to add 

a relay every time it exceeds 800 

meters, and it needs to add a relay 

every time the quantity of Modbus 

gateway exceeds 30. It needs to 

be adopted when the conditions 

are met. 

Optical isolation 

convertor 

Optical isolation 
convertor GD01 

LN02200020 

Only when BMS dopts RS232 

method should the convertor be 

adopted 

Centralized control 

cabinet 

Prepared by user 

2.2 Gateway ME30-24/D1(BM) 

2.2.1 Introduction of Functions 

Gree multi VRF protocol gateway ME30-24/D1(BM)  can realize data exchange between air 

conditioner and BMS, providing standard Modbus RTU, Modbus TCP and BACnet/IP building 

interfaces. The gateway is applicable to the Gree multi VRF unit model that adopts CAN protocol. 

 

 

 

 

Summary of Contents for VRF
































Reviews: