background image

8

Design & Selection

6 Selection of the Water Tank

6.1 Specifications of the Water Tank

SXVD200LCJ/A-K 

220~240V-1Ph-50Hz
A single coil with the electric heater is integrated, used for floor heating system 

SXVD300LCJ/A-K 
SXVD200LCJ2/A-K 

220~240V-1Ph-50Hz
Dual coils with the electric heater are integrated, used for floor heating system and the solar system

SXVD300LCJ2/A-K 
SXVD200LCJ/A-M 

380~415V-3Ph-50Hz
A single coil with the electric heater is integrated, used for floor heating system

SXVD300LCJ/A-M 

SXVD200LCJ2/A-M 

380~415V-3Ph-50Hz
Dual coils with the electric heater are integrated, used for floor heating system and the solar system

6�2 Volume Selection of the Water Tank

6.2.1 Selection Based on Water Consumption Per Capita

Building Type

Unit

Daily Water Consumption (L) 

Water Temperature (°C)

House

Per person, Per day 

40~80

60

Villa

Per person, Per day

70~110

60

6�2�2 Selection Based on Sanitary Utensils 

Utensil Type

Daily Water 

Consumption (L) 

Water Temperature (°C)

Bathtub, Sprinkler system (with shower)

150

40

Bathtub, Sprinkler system (without shower)

125

40

Shower

70~100

37~40

Wash Basin

3

30

6� 2�3 Selection of the Water Tank

Selection of the water tank should consider the flow rate of the shower head, duration of use per person 

and daily water consumption.

Volume  of the Water Tank=

t(design temperatuere)-t(entering cold water temperatuere)

t(water tank temperatuere set point)-t(entering cold wa ter temperature)

•consumptio

n

t (design temperature): generally it is 60°C ;
t (entering cold water temperature): it differs for different regions.
t ( water tank temperature set point): it is the target heating temperature of the water tank
α: correction factor

Empirical Values for Volume Correction of the Water Tank

                        Duration of Use 

                           (min/Person)

Flow Rate of the Shower Head 
                    (L/min)

10

15

20

25

30

40

4

0.48

0.71

0.94

1.18

1.42

1.89

6

0.71

1.06

1.42

1.77

2.12

2.83

8

0.95

1.42

1.89

2.36

2.83

3.77

10

1.18

1.77

2.36

2.95

3.54

4.72

15

1.76

2.65

3.54

4.42

5.31

7.08

Empirical values are worked out under conditions of 80L consumption (per day per person), 8L/min flow rate 

of the shower head, and 10 minutes use duration per person.

7 Examples for Model Selection

7�1 General Introduction to the Example Project 

For a two-floor house, there is a master room and a both room for each floor and both of 

them require floor heating. Other rooms use the heat pump for heating in winter. The master 

room covers 28m

2

 and the both room covers 12m

2

.

Summary of Contents for Versati II Series














Reviews: