Gree TTW Series Owner'S Manual Download Page 4

Do not disassemble or modify unit.

 

 

To prevent injury to the user or other people and property damage, the following instructions 

must be 

followed. Incorrect operation due to ignoring of instructions may cause harm or 

damage. The seriousness is classified by the following indications.

 

   

WARNING 

This symbol indicates the possibility of death or serious injury. 

              

CAUTION

 

           

This symbol indicates the possibility of injury or damage to property. 

 

 

 

 

      

NEVER DO THIS.

 

 

 

        ALWAYS DO THIS.

  Meaning of symbols used in this manual are as shown below.

 

      WARNING 

 

Plug in power plug properly

Do not operate or stop the unit by 

inserting or pulling out the power plug. 

Do not damage or use an 

unspecified power cord. 

Do not modify power cord length or 

share the outlet with other appliances. 

Do not operate with wet hands or  

in damp environment. 

Do not direct airflow at room

occupants only.

 

Always ensure effective grounding.  

 

Unplug the unit if strange sounds, 

smell, or smoke comes from it. 

Keep firearms away. 

 

Do not allow water to run into 

electric parts.  

Do not use the socket if it is loose or 

damaged.  

Do not use the power cord close to 

heating appliances. 

Always install circuit breaker and 

a dedicated power circuit. 

Do not open the unit during 

operation.  

Do not use the power cord near

 

flammable gas or combustibles, such as

 

gasoline, benzene, thinner, etc.

 

 It may cause fire. 

 It may cause fire and electric shock.

 

 It may cause an explosion or fire.

 

 It may cause electric shock.

 

Incorrect installation may cause fire 

and electric shock. 

 This could damage your health.

 

 If the power cord is damaged, it 

must be replaced by the 

manufacturer or an authorized 

service center in order to avoid 

hazard. 

 It may cause fire and electric shock.

 

It may cause failure of machine or 

electric shock. 

 It may cause electric shock.

 

It may cause electric shock or fire due 

to heat generation. 

  It may cause fire and electric shock.

 

Incorrect grounding may cause 

electric shock. 

It may cause electric shock or fire 

due to heat generation.

 

Otherwise, it may cause electric 

shock or fire due to excess heat 

generation.  

Ventilate room before operating air conditioner if there 

is a gas leakage from another appliance.

 

 It may cause explosion, fire and burns.

 

 It may cause failure and electric shock.

 

-1-

Summary of Contents for TTW Series

























Reviews: