Gree ME30-24/E6 Service Manual Download Page 2

To Users

Thank you for selecting Gree’s product. Please read this instruction manual carefully before installing and using the product, so

as to master and correctly use the product. In order to guide you to correctly install and use our product and achieve expected

operating effect, we hereby instruct as below:

(1)This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the

appliance by a person responsibility for their safety. Children should be supervised to ensure that they do not play with the

appliance.

(2)In order to ensure reliability of product, the product may consume some power under stand-by status for maintaining normal

communication of system and preheating refrigerant and lubricant. If the product is not to be used for long, cut off the power

supply; please energize and preheat the unit in advance before reusing it.

(3)Please properly select the model according to actual using environment, otherwise it may impact the using convenience.

(4)This product has gone through strict inspection and operational test before leaving the factory. In order to avoid damage due

to improper disassembly and inspection, which may impact the normal operation of unit, please do not disassemble the unit

by yourself. You can contact with the special maintenance center of our company if necessary.

(5)For personal injury or property loss and damage caused by improper operation such as improper installation and debugging,

unnecessary maintenance, violation of related national laws and rules and industrial standard, and violation of this

instruction manual, etc., we will bear no liability.

(6)When the product is faulted and cannot be operated, please contact with our maintenance center as soon as possible by

providing the following information.

1) Contents of nameplate of product (model, cooling/heating capacity, product No., ex-factory date).

2) Malfunction status (specify the situations before and after the error occurs).

(7)All the illustrations and information in the instruction manual are only for reference. In order to make the product better, we

will continuously conduct improvement and innovation. We have the right to make necessary revision to the product from

time to time due to the reason of sales or production, and reserve the right to revise the contents without further notice.

(8)The final right to interpret for this instruction manual belongs to Gree Electric Appliances Inc. of Zhuhai.

Summary of Contents for ME30-24/E6






















Reviews: