24
Technical Information
Service Manual
Note:
Press this button continuously more than 2s, the main unit will swing back an
●
the button, the unit will stop swinging and
forth from left to right, and then loosen
present position of guide louver will be kept immediately.
● Under swing left and right mode, when the status is switched from o f to , if
will switch to off status directly; if press
press this button again 2s later, status
this button again within 2s, the change of swing status will also depend on the
circulation sequence stated above.
Press this button can select up & down swing angle. Fan blow angle can be selected circularly as below:
● When selecting " ", air conditioner is blowing fan automaticall . Horizontal
at maximum angle.
louver will automatically swing up & down
● When selecting "
ǃ
ǃ
ǃ ǃ
", air conditioner is blowing fan at fixed
fixed position.
position. Horizontal louver will stop at the
When selecting
●
ǃ
ǃ
", air conditioner is blowing fan at fixed angle.
Horizontal louver will send air at the fixed angle.
● Hold "
button above 2s to set your required swing angle. When reaching your required angle, release the button.
Note:
● "
ǃ
ǃ
" may not be available. When air conditioner receives this signal, the air conditioner will blow fan automatically.
Press this button continuously more than 2s, the main unit will swing back an
●
the button, the unit will stop swinging and
forth from up to down, and then loosen the
present position of guide louver will be kept immediately.
● Under swing up and down mode, w en the status is switched from off to , if
will switch to off status directly; if press
press this button again 2s later, status
no display
(horizontal louvers stops
at current position)
button
7.
this button again within 2s, the change of swing status will also depend on the
circulation sequence stated above.
no display
(stops at current position)
● T-ON button
"T-ON" button can set the time for timer on. After pressing this button, " "
controller blinks. Press "▲" or
icon disappears and the word "ON" on remote
▲
" " button to adjust T-ON setting. After each pressing "▲" or " " button,
▲
T-ON setting will increase or decrease 1min. Hold "▲" or " " button, 2s
▲
your required time.
later, the time will change quickly until reaching
Press "T-ON" to confirm it. The word "ON" will stop blinking. " " icon
T-ON: Under the condition that T-ON is started up,
resumes displaying. Cancel
press "T-ON" button to cancel it.
● T-OFF button
"T-OFF" button can set the time for timer off. After pressing this button," " icon disappears and the word "OFF" on
remote controller blinks. Press "▲" or
▲
" " button to adjust T-OFF setting. After each pressing "▲" or " " button,
▲
T-OFF setting will increase or decrease 1min. Hold "▲" or "
▲
" button, 2s
your required time.
later, the time will change quickly until reaching
Press "T-OFF" word "OFF" will stop blinking. " " icon resumes displaying.
Cancel T-OFF. Under the condition that T-OFF is started up, press "T-OFF" button to cancel it.
8
8.T-ON / T-OFF button
Note:
● Under on and ff status, you can set T-OFF or T-ON simultaneously.
● Before setting T-ON or T-OFF, please adjust the clock time.
● After starting up T-ON or T-OFF, set the constant circulating valid.
After that, air conditioner will be turned on or turned off according to setting time.
ON/OFF button has no effect on setting. If you don’t need this function, please use remote controller to cancel it.
9.I FEEL button
Press this button to start I FEEL function and " " will be displayed on the remote
remote controller will send the detected
controller. After this function is set, the
ambient temperature to the controller and the unit will automatically adjust the
indoor temperature according to the detected temperature. Press this button again
disappear.
to close I FEEL function and " " will
● Please put the remote controller near ser when this function is set. Do not put
high temperature or low temperature in
the remote controller near the object of
turned on, the remote controller should be put within the area where indoor unit can receive the signal sent by the remote
controller.
order to avoid detecting inaccurate ambient temperature.When I FEEL function is
