background image

Multi Variable Air Conditioners One-way Cassette Type Indoor Unit 

 

Diameter of power cord must be 
large enough. Damaged power 
cord and connecting wire must 
be replaced by specialized 
electric cable. 

 

After the power cord is connected, 
please install the cover of electric 
box to avoid danger. 

 

Nitrogen must be charged 
according to technical 
requirements. 

 

Short circuit is forbidden. Do not 
cancel the pressure switch in case 
the unit may be damaged.   

 

For units with wired controller, do 
not connect power supply until 
the wired controller is well 
installed. Otherwise, the wired 
controller cannot be used. 

 

When the installation is finished, 
please check and make sure the 
drain pipe, pipeline and electric wire 
are all well connected in order to 
avoid water leakage, refrigerant 
leakage, electric shock or fire 
hazard. 

 

Do not extend fingers or objects 
into air outlet or air return grille. 

 

If you use gas heater or petroleum 
heater in the same room, please 
open the door or window to maintain 
good air circulation in case the room 
may lack of oxygen. 

 

Never start or stop the air 
conditioner by inserting or 
removing the power cord. 

 

Do not turn off the air conditioner 
until it runs for at least 5 minutes. 
Otherwise, oil-return of the 
compressor will be affected. 

 

Children are not allowed to 
operate the air conditioner. 

 

Do not operate the air conditioner 
with wet hands. 

 

Please turn the unit off and 
unplug your air conditioner 
before cleaning. Otherwise, it 
may cause electric shock or 
personal injury. 

 

Do not spray water on the air 
conditioner or it will cause 
malfunction or electric shock. 

 

Do not expose the air conditioner 
directly to water or place it in a 
damp or corrosive environment. 

 

Connect power supply 8 hours 
before operation. Do not disconnect 
power if you want to stop the unit in a 
short period of time, e.g. in one night 
(This is for protecting the 
compressor). 

Summary of Contents for GMV-ND22TD/A-T




























Reviews: