background image

Multi Variable Air Conditioners Ducted Type Indoor Unit 

1 Safety Precautions 

 

WARNING

 

(1)

This product can’t be installed at corrosive, inflammable or explosive environment or the place with special 

requirements, such as kitchen. Otherwise, it will affect the normal operation or shorten the service life of the 
unit, or even cause fire hazard or serious injury. As for above special places, please adopt special air conditioner 
with anti-corrosive or anti-explosion function. 

(2) Follow this instruction to complete the installation work. Please carefully read this manual before unit startup 
and service. 

(3) Wire size of power cord should be large enough. The damaged power cord and connection wire should be 
replaced by exclusive cable.   

(4) After connecting the power cord, please fix the electric box cover properly in order to avoid accident.   

(5) Never fail to comply with the nitrogen charge requirements. Charge nitrogen when welding pipes.   

(6) Never short-circuit or cancel the pressure switch to prevent unit damage.   

(7) Please firstly connect the wired controller before energization, otherwise wired controller cannot be used.   

(8) Before using the unit, please check if the piping and wiring are correct to avoid water leakage, refrigerant 
leakage, electric shock, or fire etc.   

(9) Do not insert fingers or objects into air outlet/inlet grille.   

(10) Open the door and window and keep good ventilation in the room to avoid oxygen deficit when the gas/oil 
supplied heating equipment is used.   

(11) Never start up or shut off the air conditioner by means of directly plug or unplug the power cord.   

(12) Turn off the unit after it runs at least five minutes; otherwise it will influence oil return of the compressor.   

(13) Do not allow children operate this unit.   

(14) Do not operate this unit with wet hands.   

(15) Turn off the unit or cut off the power supply before cleaning the unit, otherwise electric shock or injury may 
happen.   

(16) Never spray or flush water towards unit, otherwise malfunction or electric shock may happen.   

(17) Do not expose the unit to the moist or corrosive circumstances.   

(18) Under cooling mode, please don't set the room temperature too low and keep the temperature difference 

between indoor and outdoor unit within 5

(41

).   

(19)  User  is  not  allowed  to  repair  the  unit.  Fault  service  may  cause  electric  shock  or  fire  accidents.  Please 
contact Gree appointed service center for help.   

(20) Before installation, please check if the power supply is in accordance with the requirements specified on 
the nameplate. And also take care of the power safety.   

(21) Installation should be conducted by dealer or qualified personnel. Please do not attempt to install the unit 
by yourself. Improper handling may result in water leakage, electric shock or fire disaster etc.   

(22)  Be  sure  to  use  the  exclusive  accessory  and  part  to  prevent  the  water  leakage,  electric  shock  and  fire 
accidents.   

(23)  Make  sure  the  unit  can  be  earthed  properly  and  soundly  after  plugging  into  the  socket  so  as  to  avoid 
electric shock. Please do not connect the ground wire to gas pipe, water pipe, lightning rod or telephone line.   

(24) Electrify the unit 8 hours before operation. Please switch on for 8 hours before operation. Do not cut off 
the power when 24 hours short-time halting (to protect the compressor).   

(25) If refrigerant leakage happens during installation, please ventilate immediately. Poisonous gas will emerge 
if the refrigerant gas meets fire.   

(26)  Volatile  liquid,  such  as  diluent  or  gas  will  damage  the  unit  appearance.  Only  use  soft  cloth  with  a  little 
neutral detergent to clean the outer casing of unit.   

(27) If anything abnormal happens (such as burning smell), please power off the unit and cut off the main power 
supply, and then immediately contact Gree appointed service center. If abnormality keeps going, the unit might 
be damaged and lead to electric shock or fire.   

Any  personal  injury  or  property  loss  caused  by  improper  installation,  improper  debug, 

unnecessary repair or not following the instructions of this manual should not be the responsibility 

of Gree Electric Appliances, Inc. of Zhuhai.

 

Summary of Contents for GMV-ND18PHS/A-T



























Reviews: