background image

Multi Variable Air Conditioners Cassette Type Indoor Unit 

3.2 Installation Position Selection 

(1) The appliance shall not be installed in the laundry. 
(2) The location should be able to withstand the weight of unit. 
(3) The water can be drained conveniently from drainage pipe. 
(4) There should be no obstruction near air inlet and air outlet. 
(5) Follow the installation distance required in the fig below to ensure sufficient space for 

maintenance.   

(6) The installation location should be far from heat sources, flammable or explosive gas, or 

smog spread in the air. 

(7) The indoor unit, outdoor unit, power cord and connection electricity wire should be at least 1m 

from television and radio in order to prevent interference and noise (Even though 1m distance 
is ensure, there may be noise if the electric wave is too strong). 

Unit: mm (inch) 

 

Fig.3.2.1 

Unit: mm (inch) 

Model 

GMV-ND07~24T/C-T(U) 

280(11) 

GMV-ND30~48T/C-T(U) 

330(13) 

 

 

(1) The unit shall be installed in accordance with national standards or local regulations. 
(2) Only qualified personnel can carry out installation work, please contact with local dealer before installation. 
(3) Make sure all the installation work completed before energizing. 
(4) The appliances are not accessible to general public. 

3.3 Requirements for Communication Line 

  If air conditioner used under strong electronic-magnetic interference circumstance, STP 

(shielded twisted pair) communication cable must be adopted.     
 

Summary of Contents for GMV-ND07T/C-T


























Reviews: