background image

Multi Variable Air Conditioners Compact Cassette Type Indoor Unit 

19 

6 Routine Maintenance 

 

(1)  Do turn off the unit and cut off the main power supply when cleaning the air conditioner to 

avoid electric shock or injury. 

(2)  Stand at solid table when cleaning the unit. 

(3)  Do not clean the unit with hot water whose temperature is higher than 45°C (113°F) to prevent 

fade or deformation. 

(4)  Do not dry the filters by fire, or it may catch fire or become deformed. 

(5)  Clean the filter with a wet cloth dipped in neutral detergent. 

(6)  Please contact after-sales service staff if there is abnormal situation. 

6.1 Cleaning of Filter 

(1)  Remove the filters from inlet of IDU. Use a vacuum cleaner to remove dust. If the filters are 

dirty, wash them with warm water and mild detergent, and dry the filters in the shade. 

(2)  If the unit used in the environment with much dust, please clean it regularly. (Usually once 

every two weeks.) 

6.2 Maintenance before the Seasonal Use 

(1)  Check if the air inlet and air outlet of indoor and outdoor unit are blocked. 

(2)  Check if securely grounded. 

(3)  Check if all the power cord and communication cable are securely connected. 

(4)  Check if any error code displayed after energized. 

6.3 Maintenance after the Seasonal Use 

(1)  Set the unit in fan mode for half a day in a sunny day to dry the inner part of unit. 

(2)  When the unit won’t be used for a long time, please cut off power supply for energy saving; 

the characters on the wired controller screen will disappear after cutting off the power 

supply. 

7 Table of Error Codes for Indoor Unit 

Error 

Code 

Content 

Error 

Code 

Content 

Error 

Code 

Content 

L0 

Indoor Unit Error 

LA 

Indoor Units 

Incompatibility Error 

d9 

Jumper Cap Error 

L1 

Indoor Fan Protection 

LH 

Low Air Quality 

Warning 

dA 

Indoor Unit Network 

Address Error 

L2 

E-heater Protection 

LC 

ODU-IDU 

Incompatibility Error 

dH 

Wired Controller PCB 

Error 

L3 

Water Full Protection 

d1 

Indoor Unit PCB Error 

dC 

Capacity DIP Switch 

Setting Error. 

L4 

Wired Controller 

Power Supply Error 

d3 

Ambient Temperature 

Sensor Error 

dL 

Outlet Air 

Temperature 
Sensor Error 

L5 

Freeze protection 

d4 

Inlet Pipe Temperature 

Sensor Error 

dE 

Indoor Unit CO

2

 

Sensor Error 

Summary of Contents for GMV-ND07T/B-T


























Reviews: