17
Technical Information
Service Manual
●
When selceting " " , air conditioner is blowing fan
automatically.Horizontal louver will automatically swing up & down
at maximum angle.
●
When selecting "
" , air conditioner is
blowing fan fixed position. Horizontal louver will stop at the fixed
position.
●
Hold " " button above 2s to set your required swing angle,
When reaching your required angle, release the button.
6. LIGHT
Press this button to turn off display light on indoor unit. "
" icon
on remote controller disappears, Press this button again to turn on
display light. "
" icon is displayed.
7. SWING button
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
●
Press this button continuously more than 2s, the main unit will
swing back an forth from left to right, and then loosen the button,
the unit will stop swinging and present position of guide louver will
be kept immediately.
●
Under swing left and right mode, when the status is switched
from off to , if press this button again 2s later, status will
switch to off status directly; if press this button again within 2s,
the change of swing status will also depend on the circulation
sequence stated above.
●
This function is only available for some model.
8. TURBO
●
Under COOL or HEAT mode, press this button to turn to quick
COOL or quick HEAT mode. " " icon is displayed on remote
controller.
Press this button again to exit turbo function and " " icon will
disappear.
● If start this function, the unit will run at super-high fan speed
to cool or heat quickly so that the ambient temp. approachs the
preset temp.as soon as possible.
9. QUIET
Press this button, the Quiet status is under the Auto Quiet
mode(display "
" ) and Quiet mode (display " " ) and
Quiet OFF (there is no signal displayed), after powered on, the
Quiet OFF
is defaulted.
10. SLEEP
●
Press this button, can select Sleep 1 (
), Sleep 2 (
),
Sleep 3 ( ) and cancelthe Sleep, circulate between these, after
electrified, Sleep Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run for
one hour, the main unit setting temperature will increase 1
o
C , two
hours, setting temperature increased 2
o
C, then the unit will run at
this setting temperature; In Heat mode: sleep status after run for
one hour, the setting temperature will decrease 1
o
C , two hours,
setting temperature will decrease 2
o
C , then the unit will run at this
setting temperature.
●
Sleep 2 is sleep mode 2, that is air conditioner will run according
to the presetting a group of sleep temperature curve.
●
Sleep 3-the sleep curve setting under Sleep mode by DIY;
(1)Under Sleep 3 mode, press "Turbo" button for a long time,
remote controller enters into user individuation sleep setting
status, at this time, the time of remote controller will display
"1hour", the setting temperature "88" will display the corresponding
temperature of last setting sleep curve and blink (The first entering
will display according to the initial curve setting value of original
factory);
(2)Adjust "▲" and "
" button, could change the corresponding
setting temperature, after adjusted, press "Turbo" button for
confirmation;
(3)At this time, 1hour will be automatically increased at the timer
position on the remote controller, (that are "2hours" or "3hours"
or "8hours"), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours
temperature setting finished, sleep,curve setting finished, at this
time, the remote controller will resume the original timer display;
temperature display will resume to original setting temperature.
●
Sleep3- the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire the
presetting sleep curve, enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button
directly for confirmation. Note: In the above presetting or enquiry
procedure, if continuously within 10s, there is no button pressed,
the sleep curve setting within 10s, there is no button pressed, the
sleep curve setting status will be automatically quit and resume
to display the original displaying. In the presetting or enquiry
procedure, press "ON/OFF" button, "Mode" button, "Sleep" button,
the sleep curve setting or enquiry status will quit similarly.
11. TEMP
Press this button, could select displaying the indoor setting
temperature or indoor ambient temperature. When the indoor unit
firstly power on it will display the setting temperature, if th e te
mperature’s displaying status is changed from other status to " ",
displays the ambient temperature, 3s later or within 3s, it receives
other remote controller signal that will return to display the setting
temperature.
