background image

The Great Planes 7.2v 650 mAh NiMH (nickel-metal hydride)
battery (GPMP0068) is recommended. It is the correct size
and shape to fit in the battery holder on the Yard Stik.

The best type of charger to use is a peak charger, because
it charges the batteries until they are fully charged, then
automatically switches to a trickle charge mode. The Great
Planes ElectriFly Peak Charger (GPMM3000) is suitable for
charging the nickel-metal hydride battery recommended for
the Yard Stik.

To figure out how long it will take to charge the battery, divide
its capacity (in mAh) by the charge rate being used. If fully
discharged, the 650 mAh battery recommended for the Yard
Stik, charged at a rate of 600 mAh (by the ElectriFly Peak
Charger), will take about 65 minutes to charge (650 divided
by 600 times 60 minutes = 65). Note: It is not recommended
to charge the battery at a rate any higher than two times its
rated capacity.

IMPORTANT: Monitor the temperature of the battery frequently.
If the battery becomes warm, disconnect it from the charger.

In addition to the items previously discussed and common
building supplies and hobby tools, following is a list of the
items required to assemble the Yard Stik.

Great Planes

Pro

CA is recommended.

1/2" [13mm] double-sided foam tape (GPMQ4440)

1/2 oz. [15g] Thin Pro CA (GPMR6001)

1/2 oz. [15g] Medium Pro CA+ (GPMR6007)

#1 Hobby knife (HCAR0105)

#11 blades (5-pack, HCAR0211)

medium-grit sandpaper

Propeller balancer (TOPQ5700) (Balancing propellers
on Park Flyers is important as it will increase efficiency
and improve performance and extend run time.)

CA applicator tips (HCAR3780) 

Single-edge razor blade

2 oz. [57g] spray CA activator (GPMR6035)

APC 11 x 4.7 Slo-Flyer propeller for more performance
outdoors (APCQ5020) 

APC 9 x 4.7 Slo-Flyer propeller for better indoor flying
(APCQ5010)

Optional Items

Building Supplies

ADDITIONAL ITEMS REQUIRED

Charger

Battery

4

To order replacement parts for the Yard Stik, use the order numbers in the Replacement Parts List that follows.
Replacement parts are available only as listed. Not all parts are available separately. Replacement parts are not available
from Product Support, but can be purchased from hobby shops or mail order/Internet order firms. If you need assistance
locating a dealer to purchase parts, visit www.greatplanes.com and click on “Where to Buy.” If this kit is missing parts,
contact Great Planes Product Support.

Replacement Parts List

Order Number

Description

How to Purchase

Missing pieces ................................................Contact Product Support
Instruction manual...........................................Contact Product Support
Full-size plans .................................................Not available
Kit parts listed below.......................................Hobby Supplier

GPMA2434 ...........Wing Set
GPMA2435 ...........Fuselage Boom
GPMA2436 ...........Tail Set
GPMA2437 ...........Plastic Set
GPMA2438 ...........Landing Gear
GPMA2439 ...........Decal
GPMQ1650 ...........10 x 4.7 Propeller

ORDERING REPLACEMENT PARTS

Summary of Contents for Yard Stik

















Reviews: