background image

11

PREFLIGHT

Identify Your  Model

No matter if you fl y at an AMA sanctioned R/C club site or if 
you fl y somewhere on your own, you should always have your 
name, address, telephone number and AMA number on or 
inside your model. It is required at all AMA R/C club fl ying sites 
and AMA sanctioned fl ying events. Fill out the identifi cation 
tag on page 4 and place it on or inside your model.

Charge the Batteries

Follow the battery charging instructions that came with your 
radio control system to charge the batteries. You should 
always charge your transmitter and motor batteries the night 
before you go fl ying, and at other times as recommended by 
the manufacturer.

CAUTION:

 Unless the instructions that came with your 

radio system state differently, the 

initial

 charge on 

new 

transmitter batteries should be done for 15 hours 

using 

the slow-charger that came with the radio system

This will “condition” the batteries so that the next charge 
may be done using the fast-charger of your choice. If the 
initial charge is done with a fast-charger the batteries 
may not reach their full capacity and you may be fl ying 
with batteries that are only partially charged.

Range Check

Ground check the operational range of your radio before the 
fi rst fl ight of the day. With the transmitter antenna collapsed 
and the receiver and transmitter on, you should be able to 
walk at least 100 feet away from the model and still have 
control. Have an assistant stand by your model and, while 
you work the controls, tell you what the control surfaces are 
doing. Repeat this test with the motor running at various 
speeds with an assistant holding the model, using hand 
signals to show you what is happening. If the control surfaces 
do not respond correctly, do not fl y! Find and correct the 
problem fi rst. Look for loose servo connections or broken 
wires, corroded wires on old servo connectors, poor solder 
joints in your battery pack or a defective cell, or a damaged 
receiver crystal from a previous crash.

AMA SAFETY CODE (

EXCERPTS

)

Read and abide by the following excerpts from the Academy 
of Model Aeronautics Safety Code. For the complete Safety 
Code refer to Model Aviation magazine, the AMA web site or 
the Code that came with your AMA license.

General

1)  I will not fl y my model aircraft in sanctioned events, 

air shows, or model fl ying demonstrations until it has 
been proven to be airworthy by having been previously, 
successfully fl ight tested.

2)  I will not fl y my model aircraft higher than approximately 

400 feet within 3 miles of an airport without notifying the 
airport operator. I will give right-of-way and avoid fl ying 
in the proximity of full-scale aircraft. Where necessary, 
an observer shall be utilized to supervise fl ying to avoid 
having models fl y in the proximity of full-scale aircraft.

3)  Where established, I will abide by the safety rules for the 

fl ying site I use, and I will not willfully and deliberately fl y my 
models in a careless, reckless and/or dangerous manner.

5)  I will not fl y my model unless it is identifi ed with my name 

and address or AMA number, on or in the model. Note: 
This does not apply to models while being fl own indoors.

7)  I will not operate models with pyrotechnics (any device 

that explodes, burns, or propels a projectile of any kind).

Radio Control

1)  I will have completed a successful radio equipment ground 

check before the fi rst fl ight of a new or repaired model.

2)  I will not fl y my model aircraft in the presence of spectators 

until I become a qualifi ed fl ier, unless assisted by an 
experienced helper.

3)  At all fl ying sites a straight or curved line(s) must be 

established in front of which all fl ying takes place with the 
other side for spectators. Only personnel involved with 
fl ying the aircraft are allowed at or in the front of the fl ight 
line. Intentional fl ying behind the fl ight line is prohibited.

4)  I will operate my model using only radio control frequencies 

currently allowed by the Federal Communications Commission.

5)  

I will not knowingly operate my model within three miles 
of any pre-existing fl ying site except in accordance with 
the frequency sharing agreement listed

 [in the complete 

AMA Safety Code].

9)  Under no circumstances may a pilot or other person touch 

a powered model in fl ight; nor should any part of the 
model other than the landing gear, intentionally touch the 
ground, except while landing.

CHECK LIST

During the last few moments of preparation your mind may 
be elsewhere anticipating the excitement of the fi rst fl ight. 
Because of this, you may be more likely to overlook certain 
checks and procedures that should be performed before 
the model is fl own. To help avoid this, a check list is provided 
to make sure these important areas are not overlooked. 
Many are covered in the instruction manual, so where 
appropriate, refer to the manual for complete instructions. 
Be sure to check the items off as they are completed.

Summary of Contents for synapse arf













Reviews: