GREAT PLANES Riot 3D Instruction Manual Download Page 19

ElectriFly YAK 55 3D EP ARF
After just 2-3 hours of assembly, the YAK 55 3D EP ARF is
ready to perform high alpha flight, Harriers, Blenders, Walls
and more! It features ultra-durable FlightFlex

construction

that allows it to bounce back from crashes. With its pre-
painted, high-visibility trim scheme, the model looks as great
as it flies. A powerful Speed Force ball bearing motor and
gearbox are included, assembled and ready to install.

The YAK 55 3D EP ARF is small and quiet enough to be
flown at a park or sports field. It features large control
surfaces that deliver maximum deflection for precision
piloting, allowing you to perform nearly any 3D maneuver
you can imagine! GPMA1274

ElectriFly RimFire

Out-Runner Brushless Motor

Designed for explosive acceleration and maximum torque,
RimFire out-runner brushless motors are dependable and
virtually maintenance-free – there are not comms or brushes
to worry about, and the bearings are double-shielded. The
lightened aluminum can houses high-torque, “rare earth”
Neodymium magnet. Improved cooling means 50% more
power than other out-runners of similar size. GPMG4505

Futaba

®

4EXA 4-Channel Computer Radio

The 4EXA stores up to 4 models in memory, and lets you
call them up in seconds. Programming is easy; using just

two keys and a lever. But the 4EXA’s biggest benefit is this:
room to grow. With the 4EXA, EPA for servos, expo, wing
mixing for V-tail and elevon are at your fingertips whenever
you want them. Includes an R124 receiver, full NiCds and
three S3108M servos. 72 MHz. FUTK41**

Futaba S3110 Micro High-Torque Servo
Ideal for park flyers and small electric aircraft, Futaba’s
S3110 servo features a micro plug plus replaceable case set
and gears. FUTM0702

Futaba R124F Ultra Micro Receiver 
In park flyers, cutting even a gram from all-up weight helps
performance – a good reason to choose Futaba’s R124F. It
weighs just 0.35 oz [9.8g] with case; substitute shrink wrap
for the case, and weight drops again. Plus, it’s compatible
with the smaller, lighter micro plugs found on Futaba’s sub-
micro S3108 and S3109 park flyer servos. Fewer grams, FM
signal tech – the R1247F can offer both, on both Low and
High 72MHz bands. 1-year warranty. “Short” crystals
required. FUTL0438 – Low Band, FUTL0439 – High Band

ElectriFly Silver Series 8A Micro Brushless ESC 
If you’re into electric flight, take it easy: get a Silver Series
ESC. It’s easy to find a compatible battery – you can use
NiCd, NiMH or LiPo. Hook-up takes just seconds, and
there’s NO set-up. Silver Series ESCs detect the battery
type, read the voltage and set the voltage cut-off. Brake
turns on (or off) at your option. The BECs are hefty and
realistically rated. The SS-8 delivers 1.5A, for right-now
response and extended flight times. GPMM1800

19

Summary of Contents for Riot 3D





















Reviews: