6
❏
3. Connect the decoder to the S.Bus channel changer or
plug in the S.Bus servo. Be sure to connect it to the S.Bus port.
❏
4. Connect a 4.8V battery to the S.Bus channel changer.
❏
5. Note that the red LED is fl ashing. One fl ash per second
is connector SX1. Press and release the set switch quickly
and the light will fl ash two times per second for connector
SX2. Press it again and it will fl ash 3 times per second for
connector SX3. Set the channel changer to connector SX1.
(One fl ash per second.)
❏
5. Use the plastic screw driver to rotate the dial to channel 1.
Then press and hold the set switch. The red light will fl ash
quickly. When the red light stays on the decoder is set. Any
servo plugged into connector SX1 will operate on channel
1. Place a ch1 label on the connector.
❏
6. Follow the same procedure to set connector SX2 to
channel 5 or the channel the fl aps are set to on your transmitter.
ADDITIONAL ITEMS REQUIRED
Required Hardware and Accessories
❍
(1) Dubro #554 Large Tygon Fuel Line (DUBQ0427)
❍
(1) R/C Foam Rubber (1/4" [6mm], HCAQ1000; or 1/2"
[13mm], HCAQ1050)
❍
Propeller and spare propellers suitable for your
engine.
❍
Dubro #813 Fuel Line Barbs (DUBQ0670)
Adhesives and Building Supplies
This is the list of Adhesives and Building Supplies that are
required to fi nish the Avistar 30cc ARF.
❍
1/2 oz. [15g] Thin Pro CA (GPMR6001)
❍
Pro 30-minute epoxy (GPMR6047)
❍
Pro 6-minute epoxy (GPMR6045)
❍
Threadlocker thread locking cement (GPMR6060)
❍
Mixing sticks (50, GPMR8055)
❍
Mixing cups (GPMR8056)
❍
Epoxy brushes (6, GPMR8060)
❍
Denatured alcohol (for epoxy clean up)
❍
Masking tape
❍
Sandpaper
❍
Drill
❍
Drill bits: 1/16" [1.6 mm], 5/64" [2 mm ], 5/32" [4 mm],
11/64" [4.5 mm ], 3/16" [4.8 mm], 15/64" [6 mm], 1/4"
[6.4 mm], 25/64" [10 mm]
❍
Small metal fi le
❍
Stick-on segmented lead weights (GPMQ4485)
❍
Silver solder w/fl ux (STAR2000)
❍
Hobbico 60 Watt Soldering Iron (HCAR0776)
❍
#1 Hobby knife (RMXR6903)
❍
#11 blades (5-pack, RMXR6930)
❍
Rotary tool such as Dremel
®
❍
Rotary tool reinforced cut-off wheel (GPMR8200)
❍
DLE-30 Propeller Drill Guide (DLEQ0301)
❍
Canopy Glue Formula 560 (PAAR3300)
Covering Tools
❍
Top Flite
®
MonoKote
®
Sealing Iron (TOPR2100)
❍
Top Flite Hot Sock Iron Cover (TOPR2175)
❍
Top Flite MonoKote Trim Seal Iron (TOPR2200)
❍
Top Flite MonoKote Heat Gun (TOPR2000)
❍
Coverite
®
21st Century
®
Sealing Iron (COVR2700)
❍
Coverite 21st Century Cover Sock (COVR2702)
❍
Coverite 21st Century Trim Sealing Iron (COVR2750)
