GREAT PLAINS NTA3010 Predelivery Manual Download Page 25

Page: 25 / 47

NTA3010, NTA3510 and ADC

Table of Contents

Setup 23

2022

Table of Contents

160-220M

Charging Hydraulics

Charging Lift Hydraulics

The lift system is equipped with re-phasing hydraulic

cylinders that require a special procedure for oil fill

(charge) and bleeding air from the system. Read and

follow the procedure carefully. The re-phasing cylinders

will not function properly with air in the system.
1. Check the hydraulic fluid level in the tractor reservoir

and fill to the proper level. Add fluid to the system as

needed. A low reservoir level may draw air back into

the system and cause jerky or uneven cylinder

movements. During initial cycling of new hydraulic

cylinders, you will need about 8



gallons (32 liters)

of oil to charge empty cylinders.

2. Make sure implement frame sections are supported

by jack stands or blocks.

Refer to Figure 22

3. With the frame blocked and supported, un-pin the

rod end of the wheel cylinders. Pivot the cylinders up

and wire or otherwise safely support the rod end

higher than the base end.

Note: At the rockshaft cylinders, you may need to remove

the cylinders from the frame so that they can be

oriented with the rod end higher than the base end.

4. Set tractor flow control to 8 to 10 gpm when charging

cylinders. This avoids aerating oil and possible seal

damage with high flow tractors.

5. With the tractor engine at idle speed, energize the lift

hydraulics. When the gauge-wheel cylinders on both

wings are extended completely, hold the remote

lever on for one minute. Check all hydraulic hoses,

cylinders and fittings for leaks.

6. Retract the cylinder rods. Extend the rods again and

hold the remote lever on for one more minute.

Repeat this step two more times to charge and bleed

the system completely. Leave the cylinders un-

pinned and the drill frame supported. Again, check

all hydraulic hoses, cylinders and fittings for leaks.

7. Recheck the tractor hydraulic reservoir. Fill to the

proper level.

8. Re-pin all cylinders, and secure pins with cotter pins.
9. Slowly extend cylinders until all rods are completely

extended.

Figure 22

Support Rod End

16238

Escaping fluid under pressure can have sufficient pressure to

penetrate the skin causing serious injury. Avoid the hazard by

relieving pressure before disconnecting hydraulic lines. Use a

piece of paper or cardboard, NOT BODY PARTS, to check for

leaks. Wear protective gloves and safety glasses or goggles

when working with hydraulic systems. If an accident occurs,

seek immediate medical attention from a physician familiar

with this type of injury.

Before attempting to hydraulically lift the implement, hook the

implement to the cart and a tractor of adequate size and

power. Failure to do so could result in severe equipment

damage and bodily injury or death.

Summary of Contents for NTA3010
















































Search results

Summary of Contents for NTA3010

Reviews:

Related manuals for NTA3010

Brands by name

Popular brands

GREAT PLAINS NTA3010, Predelivery Manual

Search results

Summary of Contents for NTA3010

Reviews:

Related manuals for NTA3010

Brands by name

Popular brands