Great Computer Corporation Vogue TP-183P User Manual Download Page 36

Page: 36 / 44

TP-183P User Manual

Vogue Specification A-1

Vogue Specification

Model Name

Vogue TP-183P

Max. Media Loading Width

1900mm(74.8”)

Min. Media Loading Width

900mm(35.4”)

Max. Plotting width

1830mm(72”)

Number of Pinch Rollers

Max. Plotting Speed

Up to 1080mm/sec (42.5 ips)

Motor

DC Servo Control

Acceptable Pens

Disposable Ink and Ball Point Pens

Max. Plotting Length at one job

20m(65.6’)

Max. Roll-Media Weight

40kg

Acceptable Media (g/m²)

40g ~ 80g

Max. Roll Media Diameter

200mm(7.87”)

Roll Media Core Diameter

50mm or 76mm (2” or 3”)

Hardware Interfaces

USB, Parallel, RS-232

Data Buffer

4MB

Commands HP-GL,

HP-GL/2

Stand and Take-up System

Yes

Net Weight

105kg

Dimension(W*L*H) 750*2170*1160mm (29.5”*85.4”*45.7”)

Compatible with Windows 2000/XP/7.

The specification and data sheet may vary with different materials used. In order to obtain

the best output quality, please maintain the machine regularly and properly.

GCC reserves the right to change the specifications at any time without notice.

Summary of Contents for Vogue TP-183P













































Search results

Summary of Contents for Vogue TP-183P

Reviews:

Brands by name

Popular brands

Great Computer Corporation Vogue TP-183P, User Manual

Search results

Summary of Contents for Vogue TP-183P

Reviews:

Brands by name

Popular brands