Gravely 991082 ZT HD48 Owner'S/Operator'S Manual Download Page 23

GB - 23

Sharpen the Mower Blades

1. Remove mower blade from unit.

Discard mower blade if:

More than 1/2 in. (1.27 cm) of metal is 
removed.

Air lifts become eroded.

Blade is bent or broken.

2. Sharpen mower blade by removing an 

equal amount of material from each end 
of mower blade. DO NOT change angle 
of cutting edge or round the corner of the 
mower blade.

3. Check mower blade balance.

Slide mower blade on an unthreaded 
bolt. A balanced blade should remain in 
a horizontal position. If either end of 
mower blade moves downward, sharpen 
the heavy end until blade is balanced.

4. Install mower blade(s) on unit. 
5. Tighten the bolts to a torque of 115 – 

160 lbf-ft (156 – 217 N•m).

BATTERY

Unit comes equipped with a maintenance-
free battery that requires no regular 
maintenance except cleaning the terminals.

Remove Battery

1. Shut OFF engine. Engage parking 

brake. Remove the ignition key. 

2. Place seat in the service position (See 

Maintenance Schedule 

on page 19).

3. Disconnect cables from battery 

(negative, then positive) (Figure 11).

4. Remove hold down and remove battery.

Replace Battery

1. Replace battery and secure with battery 

hold down.

2. Reconnect cables to battery (positive, 

then negative). Position boot over 
positive terminal.

3. Return seat to operating position.

Clean Battery

Keep battery and its terminals clean. Inspect 
every 100 operating hours or monthly for best 
performance.

CAUTION: 

DO NOT sharpen 

mower blades while on unit. An 
unbalanced mower blade will 
cause excessive vibration and 
eventual damage to unit. Check 
mower blade balance before 
reinstalling blades.
NEVER weld or straighten bent 
blades.

OT0792

Figure 10

Sharpen to this pattern

1

1

4

2

4

3

1. Cutting Edge
2. Square 

Corner

3. Air Lift 

Erosion

4. Air Lift

DO NOT Sharpen to This Pattern

DISCARD if more than 
1/2 in. (1.27 cm)

WARNING: 

AVOID INJURY. 

Read and understand entire 

Safety 

section before proceeding.

WARNING: 

Battery posts, 

terminals and related accessories 
contain lead and lead 
compounds, chemicals known to 
the State of California to cause 
cancer and reproductive harm. 
Wash hands after handling.

Summary of Contents for 991082 ZT HD48









































Reviews: