background image

GB - 18

988116, 117, 120, 314

To test: 

1. With engine off, set controls as listed in line A of 

the table below.

2. Try starting the engine. See 

Starting and Shut Off 

on page 13.

IMPORTANT: 

If the system does not function properly, 

do not operate the unit until repairs are made.

3. Repeat steps 1-2 for lines B-C of the table below.

4. Shut off the unit, if necessary. See 

Shut Off

 and 

"To stop mowing."

5. With the engine running, set controls as listed in 

lines D -G of the table below.

IMPORTANT: 

If the system does not function properly, 

do not operate the unit until repairs are made.

Note:

 Unit will not start if both operator presence 

control levers are engaged.

** 

Note:

 Engine stops if both operator presence control 

levers are released while parking brake is off.

CHECK AIR CLEANER

Check the air cleaner element before each use. See 
engine manual for detailed instructions.

CHECK ENGINE OIL

Check the engine oil level before each use. Never 
operate the engine when the oil level is low. See engine 
manual for detailed instructions.

CHECK ENGINE COOLING

Check the engine air cooling system before each use. 
See engine manual for detailed instructions.

CHECK FASTENERS

Check all nuts, bolts, and other fasteners before each 
use. Replace missing or damaged fasteners.

CHECK TIRE  PRESSURE

Check tires for proper inflation, excessive wear or 
damage before each use. The correct air pressure is 
8 to 16 psi (55 to 110 kPa).

CHECK HYDRAULIC FLUID LEVEL

Check the hydraulic fluid level with the dipstick before 
each use (more often if leaks are observed). Stop the 
engine before servicing any hydraulic parts.

1. Run unit until warm.

2. Shut off engine.

3. Unscrew tank cap to remove cap/dipstick.

NOTE: 

Do not allow any dirt to get into the system.

4. Wipe dipstick clean.

5. Screw cap/dipstick back into tank.

6. Remove cap/dipstick and check hydraulic oil level 

mark.

7. Add hydraulic fluid as needed. Do not overfill. See 

Specifications

 for hydraulic fluid type.

CHECK BATTERY (988108, 109, 117)

Terminals

Inspect battery and terminals every 25 hours. 

PT

O

P

ARKING BRAKE

OPERA

T

OR PRESENCE 

CONTR

OL

ENGINE

A

Off

Off

Off

Won’t Start

B

Off

On

Off

Starts

C

Off

On

On*

Starts

D

Won’t Run

On

Off

Runs

E

On/Off

Off

Off**

Stops

F

Off

Off

Off

Stops

G

Off

On

Off

Runs

WARNING: HYDRAULIC FLUID UNDER 
PRESSURE

 can penetrate skin and cause 

severe burns that can result in death or 
serious injury.

ALWAYS keep body and hands away from 
pin holes or nozzles which eject hydraulic 
fluid under pressure. ALWAYS use paper or 
cardboard and not hands to search for leaks.

KNOW that all hydraulic fluid connections 
are tight and all hydraulic hoses and lines 
are in good condition BEFORE applying 
pressure to system.

Foreign fluid injected into skin must be 
surgically removed within a few hours by a 
doctor familiar with this form of injury or 
gangrene may result.

WARNING: 

AVOID INJURY. Read and 

understand the entire 

Safety 

section before 

proceeding.

WARNING: 

Battery posts, terminals and 

related accessories contain lead and lead 
compounds, chemicals known to the State of 
California to cause cancer and reproductive 
harm. Wash hands after handling.

Summary of Contents for 988105


































Reviews: