background image

ULTRAMAT AC/DC EQ

19

◎ ENVIRONMENT PROTECTION NOTES

◎ SAFETY APPROVAL

14.  Never charge Lithium battery packs above their maximum charge rate. This can dam-

age the pack and can be dangerous. Generally, Lithium Polymer packs should not be 

charged above 2C (2 x Capacity). However, some newer packs do allow charging at up 

to 5C, but charging at these higher rates will   reduce the life of the pack.

  e.g Pack of 2500mAh capacity : 2C = 5000mAh = 5A max charge current.

15.  Do not use discharge rates in excess of those specified with the battery pack as this 

will result in a significant drop in voltage under load and will dramatically reduce the 

number of charge/discharge cycles the battery pack will give. If disposing of Lithium 

battery packs ensure that the pack is fully discharged by using a light bulb, electric 

motor or similar to completely discharge the pack.

16.  Before charging any Lithium battery packs they should be closely inspected for any 

damage, such as punctures in the sleeving or if the battery has swollen or expanded 

in size. If any such damage is detected Do not charge, even if the battery otherwise 

appears to be brand new.

17.  Before commencing charging always double check the settings on the charger to 

ensure it is set correctly for the battery pack to be charged. Using the wrong settings 

is likely to result in damage to the battery pack being charged and could result in the 

battery catching fire.

This product must not be disposed of with other waste. Instead, it is the 

user’s responsibility to their waste equipment by handing it over to a 

designated collection point for the recycling of waste electrical and elec-

tronic equipment. The separate collection and recycling of your waste 

equipment at the time of disposal will help to conserve natural resourc-

es and ensure that it is recycled in a manner that protects human health 

and the environment. For more information about where you can drop 

off your waste equipment for recycling, please contact your local city 

office, your household waste disposal service or where you purchased 

the produce

Do not allow any Lithium battery pack to short-circuit as this is 
likely to result in a minor explosion and consequent fire.

   DECLARATION OF CONFORMITY

We hereby declare that the flowing product

Product: Graupner/SJ ULTRAMAT AC/DC EQ Charger

Confirms with the essential protective requirements as laid down in the directive for 

harmonizing the statutory directives of the member states concerning electro-magnetic 

interference

The applicant may issue a DECLARATION of CONFIRMITY and apply the CE marking in 

accordance with European Union Rules

   KC Information

Product: Graupner/SJ ULTRAMAT AC/DC EQ Charger

국립전파 연구원의 전자파 적합등록을 획득하였습니다. 

Summary of Contents for ULTRAMAT AC/DC EQ





















Reviews: