GRAUPNER MZ-8 Quick Start Manual Download Page 6

P6 
안전규격 

 
(1) KC  인증   
 

Graupner    mz-8 Transmitter 

KCC인증번호: MSIP-CRM-sjr-16006700

 

 
 
 

(2)

 Conformite Europeenne 

Product(s): Graupner    mz-8 Transmitter, 
 

 

 

 

(3)

 

FCC Information 

Graupner mz-8 Transmitter 

FCC ID: SNL-16006700 

 
FCC Statement 

1. This device complies with Part 15 of the FCC 

Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including 
interference that may cause undesired operation. 
 
2. Changes or modifications not expressly approved by the party 
responsible for compliance could void the user

s authority to operate 

the equipment. 

 

•   

NOTE 

This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation.   
If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- _Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected. 
- Consult the dealer or an experienced radio/TV technician for help. 

 
 
 

•   

 

◎ 

Notes on environmental protection 

This  symbol  on  the  product,  user 
manual or packaging indicates that this 
product  must  not  be  disposed  of  with 
other household waste at the end of its 
life. It must be handed over 
to the applicable collection point for the 
recycling  of  electrical  and  electronic 

equipment. 
The  materials  are  recyclable  as  marked.  By  recycling, 
material reusing  or other forms of scrap usage you  are 
making  an  important  contribution  to  environmental 
protection. 
Batteries  and  accumulators  must  be  removed  from  the 
device and disposed of at an appropriate collection point. 
Please  inquire  if  necessary  from  the  local  authority  for 
the appropriate disposal site.

 

 

Summary of Contents for MZ-8







Reviews: