background image

GRAUPNER/SJ GmbH D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors.  

 

    11/2013 

5

 

Connect the servo leads to the receiver in the following sequence: speed controller to 
socket 

1

, aileron servo to socket 

2

, elevator servo to socket 

3

, rudder servo to socket 

4

, retractable power unit servo to socket 

6

Caution:  please  refer  to  the  diagram  on  the  receiver  itself  to  ensure  that  the 
leads are connected correctly: the brown or black wire should always be at the 
top of the receiver. 

 

 

The picture shows the receiver with all connections complete; it is installed across the 
bottom  of  the  fuselage.  Pierce  a  hole  through  the  right-hand  fuselage  side  for  the 
receiver aerial. 

 

 

 

The illustration shows the LiPo battery (3/1600 / 11.1 V) installed in the fuselage. It is 
retained  by  a  strip  of  hook-and-loop  tape  about  30  mm  long,  applied  to  the  battery 
itself.  Please  remember  that  the  action  of  connecting  the  G3.5  plugs  and  sockets 
switches  the  receiver  on.  In  this  state  unforeseen  circumstances  could  cause  the 
motor to burst into life without warning. 
 

Caution:  on  no  account  touch  the  fan  once  the  G3.5  plugs  and  sockets  are 
connected, and keep all objects well clear of it. If you overlook this, the result 
could be serious injury to hands, face or eyes. 

 
Replace the canopy on the fuselage, and your 

HoTT-FAN

 is ready to fly. 

Summary of Contents for HoTT-FAN











Reviews: