manualshive.com logo in svg

GRAUPNER FOCKE WULF 190 D, Instructions Manual, Page: 8 / 14

Share
Download
GRAUPNER FOCKE WULF 190 D Instructions Manual Download Page 8

GRAUPNER GmbH & Co. KG      D-73230 KIRCHHEIM/TECK      GERMANY

    

No liability for printing errors. We reserve the right to introduce modifications. 

                                                         02/2007 

8

otherwise you will not obtain strong, durable joints. This applies in particular to 
moulded GRP fuselages. 

 

Additional items required 
 
Motor and accessories 

Motor 
Order No. 

Capacity 
cc 

Silencer 
Order No. 

Propeller 
Order No. 

OS MAX FS 91 
SURPASS II-P 

1894 

14.95 

1821.33 

34 x 20 cm 

1316.34.20 

OS MAX FS 120 
SURPASS III 

1886 

19.96 

1886.33 

36 x 18 cm 

1316.36.18 

OS MAX FS 120 
SURPASS-E 

1848 

19.96 

1886.33 

36 x 18 cm 

1316.36.18 

OS MAX 120 AX 

2703 

20.00 

2703.33

 + 

38 x 25 cm 

1318.38.25 

 
 

Radio control system 
For this model you require at least a six-channel RC system with eight servos. The 
transmitter should also feature a servo reverse facility. 

We particularly recommend mc-22 to mc-24 computer systems. The model is designed 
for standard-size servos. 
We recommend the following receiver battery: GMVIS GP 3300 NiMH, Order No. 
2573.4, which should be properly maintained before and after each flying session. 
Please remember that the pack needs to be cycled (charged and discharged) several 
times before it reaches full rated capacity. 
 
For connecting the aileron, landing flap and retract servos to the receiver you will need 
five suppressor filters, Order No. 1040, or a folding ferrite ring, Order No. 98516.1, 
together with five extension leads, Order No. 3935.11. The two aileron servo leads 
should be extended using extension leads, Order No. 3935.32, the two flap servo leads 
with Order No. 3935.11. 
Foam padding for the receiver and receiver battery is included in the kit. 
The model is designed for standard-sized servos. 
 

Adhesives 

Fast-setting epoxy resin, e.g. UHU plus schnellfest, Order No. 962 
Slow-setting epoxy resin, e.g. UHU plus endfest, Order No. 950 
White glue, e.g. UHU coll, Order No. 958.60 
UHU hart cellulose cement, e.g. Order No. 534 
UHU ALLESKLEBER Kraft, Order No. 1096 
Cyano-acrylate glue (“cyano”), e.g. Order No. 5821 
Thread-lock fluid, e.g. Order No. 952 
 

Accessories for flying the model

 (not included) 

Synthetic oil based glow fuel, to suit motor 
Fuel filter, e.g. Order No. 1650.1 
Fuel tubing, e.g. Order No. 1643, for glow motors 

Summary of Contents for FOCKE WULF 190 D















Reviews:

No comments