GRAUPNER FOCKE WULF 190 D Instructions Manual Download Page 2

GRAUPNER GmbH & Co. KG      D-73230 KIRCHHEIM/TECK      GERMANY

    

No liability for printing errors. We reserve the right to introduce modifications. 

                                                         02/2007 

2

Caution! do not heat the film more than is absolutely necessary. If the air or the iron is 
too hot, the film may melt and holes may be formed. 
 
This model is highly pre-fabricated and can be built in a very short time. However, the 
work which you have to carry out is important and must be done carefully. The model 
will only be strong and fly well if you complete your tasks competently - so please work 
slowly and accurately. 
 

When self-tapping screws have to be screwed into wood, apply a little white glue 
to prevent them shaking loose: just squirt white glue into the hole and fit the 
screw. 

 
 

Safety notes and warnings relating to model  
aircraft powered by glowplug motors 
 

• 

Be sure to read right through the instructions covering assembly and 
operation of your model before you attempt to operate it for the first time. 

• 

These safety notes are an integral part of the instructions. Please keep them 
and the operating instructions in a safe place. If you ever dispose of the model 
be sure to pass them on to the new owner. 

• 

Powered model aircraft are very demanding and potentially dangerous 
machines, and call for a high level of technical knowledge and skill from the 
operator, together with a responsible attitude. 

• 

Powered model aircraft are not suitable for young persons under eighteen 
years of age. 

• 

Young people should only be permitted to operate this model under the 
instruction and supervision of an adult who is aware of the hazards involved 
in this activity. 

• 

The operator of the model must be in full possession of his or her bodily and 
mental faculties. As with car driving, operating a model aircraft under the 
influence of alcohol or drugs is not permissible under any circumstances. 

 
 

• 

Radio-controlled model aircraft may only be employed for the purpose 
intended by the manufacturer. They must never be used as man-carrying 
machines. We do not permit this model’s use in any way except as a model 
aircraft. 

• 

A radio-controlled model aircraft can only work properly and fulfil your 
expectations if it is built very carefully and in accordance with the building 
instructions. Do not make any modifications of any kind to the design features 
or materials. If you wish to avoid injuring people and damaging property it is 
essential to be careful and painstaking at all stages of building and operating 
your model. Nobody would climb into a full-size aircraft and try to fly it without 
completing a course of training first. Model flying is a skill which has to be 
learned in just the same way. We suggest that you ask for help from an 
experienced model flyer, or join a model club or flight training school. Your 
local model shop and the specialist magazines are excellent sources of 
information. 

• 

It is fundamentally essential to set the Centre of Gravity (CG) and control 
surface travels correctly. Adjust the model until they are exactly correct. 

Summary of Contents for FOCKE WULF 190 D















Reviews: