GRAUPNER FOCKE WULF 190 D Instructions Manual Download Page 1 | Manualshive

Page: 1 / 14

GRAUPNER FOCKE WULF 190 D Instructions Manual Download Page 1

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

No liability for printing errors. We reserve the right to introduce modifications.

02/2007

1

Order No.

9395

Instructions

FOCKE WULF 190 D

For glowplug motors up to 20 cc capacity

The model requires at least a six-channel radio control system

Specification

Wingspan approx.

1740 mm

Length excl. spinner approx.

1620 mm

Wing area approx.

63 dm²

All-up weight according to fittings approx.

4600 g

Longitudinal dihedral

approx. 0.5°

CG approx.

115 - 125 mm aft of the

wing root leading edge

Caution:

This model is not a toy!

If you are a beginner to this type of powered model, please ask an experienced model
flyer for help and support. If you attempt to operate the model without knowing what you
are doing, you could easily injure yourself or somebody else. Please keep your safety
and well-being in mind at all times.

Important: before you start construction

Even if you have already built a large number of RC models please read right through
these instructions and check that all the kit components are actually present. We have
taken great trouble to keep construction as simple as possible, without making any
compromises in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the film covering due to major fluctuations in
weather conditions (temperature, humidity etc.); in rare cases you may even find a slight
warp in a component. These minor faults are in the nature of film-covered built-up
wooden structures, and can easily be corrected using a heat gun, as commonly used for
modelling.
Creases:

Blow warm air over the area and rub down with a soft cloth.

Wing warp:

Hold the panel twisted gently in the opposite direction to the warp, and
apply warm air to remove the creases from the covering.

1
2
3
...
»

Summary of Contents for FOCKE WULF 190 D















Reviews:

No comments