GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 31 / 346

background image

low cost, high capacity drives, such as 7.2K SAS drives. In a typical workflow, production is finished
on the production storage and then the content is pushed to an online K2 system for playout.
Production storage is configured similar to Online storage, but with the 7.2K SAS RAID devices
and drives. Production storage can be iSCSI or Fibre Channel.

Nearline

– Nearline storage is considered “Tier 3” K2 storage in that it is suitable for media file

transfer but does not support either record or play. The purpose of a nearline SAN is to provide a
large pool of storage to which files can be saved. The nearline system is considered an “offline”
system, which means the system stores files only, such GXF files or MXF files, with no ability to
record or play those files directly on the system. The files on a nearline system can be readily
available to an online K2 system via FTP or CIFS connections over Ethernet. Nearline storage has
Fibre Channel connections between the K2 Media Server and the RAID storage devices.

Workgroup

– Workgroup storage is a Fibre-Channel-only type of production storage intended for

small workgroups. This type of storage is no longer recommended, as technology advances provide
better value with standard iSCSI Production storage.

Live Production

– In K2Config you can create a Live Production K2 SAN. This mode can be

applied to online and production SANs. A K2 SAN with Live Production mode has a shorter minimum
delay between start record and start playout and is ideal for use with K2 Dyno. To support this mode,
Grass Valley must design your K2 SAN for increased bandwidth.

Stand-alone

– This is not shared storage. It is the local storage for a K2 Media Client, K2 Summit

Production Client, or K2 Solo Media Server. Stand-alone storage can be internal media drives or
direct-connect K2 RAID devices. Refer to the

K2 System Guide

.

K2 SAN descriptions

The following sections describe the standard, pre-defined structures of the K2 SAN. Refer to related
topics in this document for more information on custom K2 SAN systems.

Related Topics

About custom K2 SAN systems

on page 325

2014 01 27

K2 SAN Installation and Service Manual

31

Product description

«
...
29
30
31
32
33
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Azure StorSimple 8100

Brand: Microsoft Pages: 12

Brand: Sans Digital Pages: 2

Duramax Yardmate

Brand: USP Pages: 25

Brand: Homak Pages: 3

Brand: National Instruments Pages: 20

Brand: Overland Storage Pages: 4

HTS723212L9A360

Brand: Hitachi Pages: 176

HTS723212L9A360

Brand: Hitachi Pages: 5

Brand: Dell Pages: 396

Brand: Dell Pages: 180

EqualLogic PS6010

Brand: Dell Pages: 57

PowerVault 700N

Brand: Dell Pages: 29

Brand: Dell Pages: 133

Brand: SanDisk Pages: 1

FARTOOLS BRICO WB 100

Brand: Far Group Pages: 8

Brand: U-Line Pages: 6

Brand: StorageTek Pages: 86

Metalworker CBGS2

Brand: Clarke Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands